Product Description
45mm 12V High Torque Low Speed Planetary Gear Motor
Gearbox data:
| Number of stages | 1stages reduction | 2 stages reduction | 3 stages reduction | 4 stages reduction | 5 stages reduction |
| Reduction ratio | 3.7,5.2 | 13.7,19.2,26.9 | 50.9,71.2,99.5,139 | 188,264,369,516,721 | 669,977,1367,1911,2672,3736, |
| gearbox length ” L” mm | 26.4 | 32.6 | 38.9 | 45.3 | 52.5 |
| Max.Running torque | 3.0Kgf · cm | 6.0Kgf · cm | 8.0Kgf · cm | 12.0Kgf · cm | 20Kgf · cm |
| Max. Gear breaking torque | 9.0Kgf · cm | 18.0Kgf · cm | 24Kgf · cm | 36Kgf · cm | 60Kgf · cm |
| Max. Gearing efficiency | 90% | 81% | 73% | 65% |
Motor data:
| Motor name | Rated volt.v | No load | Load torque | Stall torque | |||||||||||||||||
| Current | Speed | Current | Speed | Torque | Output power | Torque | Current | ||||||||||||||
| mA | r/min | mA | r/min | gf · cm | W | gf · cm | mA | ||||||||||||||
| RS-555123 | 12 | ≤220 | 45 | 12 | ≤350 | 6 | 24 | ≤70 | 3 | 24 | ≤110 | 45 | 24 | ≤180 | 6000 | ≤1000 | 4500 | 300 | 13.5 | 1200 | 4000 |
| 1,This table lists some motors parameters, others please refer to specific parameters of rs-555.htm” 2,Afier connecting motor and gearbox which is named gearmotor the output torque:motor torque X reduction ratio X gearing efficiency;output speed:motor speed / reduction ratio. |
|||||||||||||||||||||
Company Introduction
| Output Speed: | 0.5rpm—2000rpm |
|---|---|
| Gears: | Metal Gear,Powder Metallurgy |
| Gearing Arrangement: | Planetary |
| Power: | DC |
| Drive Motor: | Low Noise |
| Motor: | with Gearbox |
| Customization: |
Available
| Customized Request |
|---|
Dynamic Modeling of a Planetary Motor
A planetary gear motor consists of a series of gears rotating in perfect synchrony, allowing them to deliver torque in a higher output capacity than a spur gear motor. Unlike the planetary motor, spur gear motors are simpler to build and cost less, but they are better for applications requiring lower torque output. That is because each gear carries the entire load. The following are some key differences between the two types of gearmotors.
planetary gear system
A planetary gear transmission is a type of gear mechanism that transfers torque from one source to another, usually a rotary motion. Moreover, this type of gear transmission requires dynamic modeling to investigate its durability and reliability. Previous studies included both uncoupled and coupled meshing models for the analysis of planetary gear transmission. The combined model considers both the shaft structural stiffness and the bearing support stiffness. In some applications, the flexible planetary gear may affect the dynamic response of the system.
In a planetary gear device, the axial end surface of the cylindrical portion is rotatable relative to the separating plate. This mechanism retains lubricant. It is also capable of preventing foreign particles from entering the planetary gear system. A planetary gear device is a great choice if your planetary motor’s speed is high. A high-quality planetary gear system can provide a superior performance than conventional systems.
A planetary gear system is a complex mechanism, involving three moving links that are connected to each other through joints. The sun gear acts as an input and the planet gears act as outputs. They rotate about their axes at a ratio determined by the number of teeth on each gear. The sun gear has 24 teeth, while the planet gears have three-quarters that ratio. This ratio makes a planetary motor extremely efficient.
planetary gear train
To predict the free vibration response of a planetary motor gear train, it is essential to develop a mathematical model for the system. Previously, static and dynamic models were used to study the behavior of planetary motor gear trains. In this study, a dynamic model was developed to investigate the effects of key design parameters on the vibratory response. Key parameters for planetary gear transmissions include the structure stiffness and mesh stiffness, and the mass and location of the shaft and bearing supports.
The design of the planetary motor gear train consists of several stages that can run with variable input speeds. The design of the gear train enables the transmission of high torques by dividing the load across multiple planetary gears. In addition, the planetary gear train has multiple teeth which mesh simultaneously in operation. This design also allows for higher efficiency and transmittable torque. Here are some other advantages of planetary motor gear trains. All these advantages make planetary motor gear trains one of the most popular types of planetary motors.
The compact footprint of planetary gears allows for excellent heat dissipation. High speeds and sustained performances will require lubrication. This lubricant can also reduce noise and vibration. But if these characteristics are not desirable for your application, you can choose a different gear type. Alternatively, if you want to maintain high performance, a planetary motor gear train will be the best choice. So, what are the advantages of planetary motor gears?
planetary gear train with fixed carrier train ratio
The planetary gear train is a common type of transmission in various machines. Its main advantages are high efficiency, compactness, large transmission ratio, and power-to-weight ratio. This type of gear train is a combination of spur gears, single-helical gears, and herringbone gears. Herringbone planetary gears have lower axial force and high load carrying capacity. Herringbone planetary gears are commonly used in heavy machinery and transmissions of large vehicles.
To use a planetary gear train with a fixed carrier train ratio, the first and second planets must be in a carrier position. The first planet is rotated so that its teeth mesh with the sun’s. The second planet, however, cannot rotate. It must be in a carrier position so that it can mesh with the sun. This requires a high degree of precision, so the planetary gear train is usually made of multiple sets. A little analysis will simplify this design.
The planetary gear train is made up of three components. The outer ring gear is supported by a ring gear. Each gear is positioned at a specific angle relative to one another. This allows the gears to rotate at a fixed rate while transferring the motion. This design is also popular in bicycles and other small vehicles. If the planetary gear train has several stages, multiple ring gears may be shared. A stationary ring gear is also used in pencil sharpener mechanisms. Planet gears are extended into cylindrical cutters. The ring gear is stationary and the planet gears rotate around a sun axis. In the case of this design, the outer ring gear will have a -3/2 planet gear ratio.
planetary gear train with zero helix angle
The torque distribution in a planetary gear is skewed, and this will drastically reduce the load carrying capacity of a needle bearing, and therefore the life of the bearing. To better understand how this can affect a gear train, we will examine two studies conducted on the load distribution of a planetary gear with a zero helix angle. The first study was done with a highly specialized program from the bearing manufacturer INA/FAG. The red line represents the load distribution along a needle roller in a zero helix gear, while the green line corresponds to the same distribution of loads in a 15 degree helix angle gear.
Another method for determining a gear’s helix angle is to consider the ratio of the sun and planet gears. While the sun gear is normally on the input side, the planet gears are on the output side. The sun gear is stationary. The two gears are in engagement with a ring gear that rotates 45 degrees clockwise. Both gears are attached to pins that support the planet gears. In the figure below, you can see the tangential and axial gear mesh forces on a planetary gear train.
Another method used for calculating power loss in a planetary gear train is the use of an auto transmission. This type of gear provides balanced performance in both power efficiency and load capacity. Despite the complexities, this method provides a more accurate analysis of how the helix angle affects power loss in a planetary gear train. If you’re interested in reducing the power loss of a planetary gear train, read on!
planetary gear train with spur gears
A planetary gearset is a type of mechanical drive system that uses spur gears that move in opposite directions within a plane. Spur gears are one of the more basic types of gears, as they don’t require any specialty cuts or angles to work. Instead, spur gears use a complex tooth shape to determine where the teeth will make contact. This in turn, will determine the amount of power, torque, and speed they can produce.
A two-stage planetary gear train with spur gears is also possible to run at variable input speeds. For such a setup, a mathematical model of the gear train is developed. Simulation of the dynamic behaviour highlights the non-stationary effects, and the results are in good agreement with the experimental data. As the ratio of spur gears to spur gears is not constant, it is called a dedendum.
A planetary gear train with spur gears is a type of epicyclic gear train. In this case, spur gears run between gears that contain both internal and external teeth. The circumferential motion of the spur gears is analogous to the rotation of planets in the solar system. There are four main components of a planetary gear train. The planet gear is positioned inside the sun gear and rotates to transfer motion to the sun gear. The planet gears are mounted on a joint carrier that is connected to the output shaft.
planetary gear train with helical gears
A planetary gear train with helical teeth is an extremely powerful transmission system that can provide high levels of power density. Helical gears are used to increase efficiency by providing a more efficient alternative to conventional worm gears. This type of transmission has the potential to improve the overall performance of a system, and its benefits extend far beyond the power density. But what makes this transmission system so appealing? What are the key factors to consider when designing this type of transmission system?
The most basic planetary train consists of the sun gear, planet gear, and ring gear elements. The number of planets varies, but the basic structure of planetary gears is similar. A simple planetary geartrain has the sun gear driving a carrier assembly. The number of planets can be as low as two or as high as six. A planetary gear train has a low mass inertia and is compact and reliable.
The mesh phase properties of a planetary gear train are particularly important in designing the profiles. Various parameters such as mesh phase difference and tooth profile modifications must be studied in depth in order to fully understand the dynamic characteristics of a PGT. These factors, together with others, determine the helical gears’ performance. It is therefore essential to understand the mesh phase of a planetary gear train to design it effectively.
editor by CX 2023-05-25
China Best Sales Factory Wholesale DC Brushed 42mm 12V 24V 48V 10.4W 21.1W 50rpm Electric Planetary Gear Reduction Motor with Encoder High Torque motor engine
Product Description
| BG 42ZYT DC Brushed Motor | |
| Environmental Conditions | -20ºC~50ºC |
| Insulation Clase | B |
| Protection class | IP44 |
| Noise | ≤65dB |
| Number of phases | Single |
| Lifespan | >1000h |
| Electrical Specifications | |||||||||
| Model | RATED LOAD | NO LOAD | STALL | ||||||
| Voltage | Power |
Speed |
Torque | Current | Speed | Current | Torque | Current | |
| V | W | rpm | N.m | A | rpm | A | N.m | A | |
| BG 42775-1 | 12 | 10.4 | 2430 | 0.04 | 1.3 | 3000 | 0.4 | 0.25 | 6.7 |
| BG 42775-2 | 24 | 21.1 | 3850 | 0.05 | 1.25 | 4500 | 0.25 | 0.4 | 8.3 |
| We can also customize products according to customer requirements. | |||||||||
| Planetary Gear Motor Technical Data-BG | ||||||||
| Ratio | 10.2 | 19.2 | 26.9 | 188 | 264 | 721 | 669 | 1911 |
| NO-load speed | 1167 | 700 | 437 | 175 | 98 | 87.5 | 58 | 36 |
| Rated speed(rpm) | 1000 | 600 | 375 | 150 | 83 | 75 | 50 | 31 |
| Rated torque | 0.34 | 0.65 | 0.9 | 5.6 | 6 | 6 | 6 | 6 |
Established in 1994, HangZhou BG Motor Factory is a professional manufacturer of brushless DC motors, brushed DC motors, planetary gear motors, worm gear motors, Universal motors and AC motors. We have a plant area of 6000 square meters, multiple patent certificates, and we have the independent design and development capabilities and strong technical force, with an annual output of more than 1 million units. Since the beginning of its establishment, BG motor has focused on the overall solution of motors. We manufacture and design motors, provide professional customized services, respond quickly to customer needs, and actively help customers to solve problems. Our motor products are exported to 20 countries, including the United States, Germany, Italy, the United Kingdom, Poland, Slovenia, Switzerland, Sweden, Singapore, South Korea etc.
Our founder, Mr. Sun, has more than 40 years of experience in motor technology, and our other engineers also have more than 15 years of experience, and 60% of our staff have more than 10 years of experience, and we can assure you that the quality of our motors is top notch.
The products cover AGV, underwater robots, robots, sewing machine industry, automobiles, medical equipment, automatic doors, lifting equipment, industrial equipment and have a wide range of applications.
We strive for CZPT in the quality of each product, and we are only a small and sophisticated manufacturer.
Our vision: Drive the world forward and make life better!
Q:1.What kind of motors can you provide?
A:At present, we mainly produce brushless DC motors, brush DC motors, AC motors, Universal Motors; the power of the motor is less than 5000W, and the diameter of the motor is not more than 200mm;
Q:2.Can you send me a price list?
A:For all of our motors, they are customized based on different requirements like lifetime, noise,voltage,and shaft etc. The price also varies according to annual quantity. So it’s really difficult for us to provide a price list. If you can share your detailed requirements and annual quantity, we’ll see what offer we can provide.
Q:3.Can l get some samples?
A:It depends. If only a few samples for personal use or replacement, I am afraid it’ll be difficult for us to provide because all of our motors are custom made and no stock available if there are no further needs. If just sample testing before the official order and our MOQ,price and other terms are acceptable,we’d love to provide samples.
Q4:Can you provide OEM or ODM service?
A:Yes,OEM and ODM are both available, we have the professional R&D dept which can provide professional solutions for you.
Q5:Can l visit your factory before we place an order?
A:welcome to visit our factory,wear every pleased if we have the chance to know each other more.
Q:6.What’s the lead time for a regular order?
A:For orders, the standard lead time is 15-20 days and this time can be shorter or longer based on the different model,period and quantity.
| Application: | Universal, Industrial, Household Appliances, Car, Power Tools, Robot Arm |
|---|---|
| Operating Speed: | Low Speed |
| Excitation Mode: | DC |
| Function: | Driving |
| Casing Protection: | Closed Type |
| Number of Poles: | Can Be Choosen |
| Samples: |
US$ 0/Piece
1 Piece(Min.Order) | |
|---|
| Customization: |
Available
| Customized Request |
|---|
The Basics of a Gear Motor
The basic mechanism behind the gear motor is the principle of conservation of angular momentum. The smaller the gear, the more RPM it covers and the larger the gear, the more torque it produces. The ratio of angular velocity of two gears is called the gear ratio. Moreover, the same principle applies to multiple gears. This means that the direction of rotation of each adjacent gear is always the opposite of the one it is attached to.
Induction worm gear motor
If you’re looking for an electric motor that can deliver high torque, an Induction worm gear motor might be the right choice. This type of motor utilizes a worm gear attached to the motor to rotate a main gear. Because this type of motor is more efficient than other types of motors, it can be used in applications requiring massive reduction ratios, as it is able to provide more torque at a lower speed.
The worm gear motor is designed with a spiral shaft that is set into splines in another gear. The speed at which the worm gear rotates is dependent on the torque produced by the main gear. Induction worm gear motors are best suited for use in low-voltage applications such as electric cars, renewable energy systems, and industrial equipment. They come with a wide range of power-supply options, including twelve-volt, 24-volt, and 36-volt AC power supplies.
These types of motors can be used in many industrial settings, including elevators, airport equipment, food packaging facilities, and more. They also produce less noise than other types of motors, which makes them a popular choice for manufacturers with limited space. The efficiency of worm gearmotors makes them an excellent choice for applications where noise is an issue. Induction worm gear motors can be compact and extremely high-torque.
While the Induction worm gear motor is most widely used in industrial applications, there are other kinds of gearmotors available. Some types are more efficient than others, and some are more expensive than others. For your application, choosing the correct motor and gearbox combination is crucial to achieving the desired result. You’ll find that the Induction worm gear motor is an excellent choice for many applications. The benefits of an Induction worm gear motor can’t be overstated.
The DC gear motor is an excellent choice for high-end industrial applications. This type of gearmotor is smaller and lighter than a standard AC motor and can deliver up to 200 watts of torque. A gear ratio of three to two can be found in these motors, which makes them ideal for a wide range of applications. A high-quality DC gear motor is a great choice for many industrial applications, as they can be highly efficient and provide a high level of reliability.
Electric gear motors are a versatile and widely used type of electric motor. Nevertheless, there are some applications that don’t benefit from them, such as applications with high shaft speed and low torque. Applications such as fan motors, pump and scanning machines are examples of such high-speed and high-torque demands. The most important consideration when choosing a gearmotor is its efficiency. Choosing the right size will ensure the motor runs efficiently at peak efficiency and will last for years.
Parallel shaft helical gear motor
The FC series parallel shaft helical gearmotor is a compact, lightweight, and high-performance unit that utilizes a parallel shaft structure. Its compact design is complemented by high transmission efficiency and high carrying capacity. The motor’s material is 20CrMnTi alloy steel. The unit comes with either a flanged input or bolt-on feet for installation. Its low noise and compact design make it an ideal choice for a variety of applications.
The helical gears are usually arranged in two rows of one another. Each row contains one or more rows of teeth. The parallel row has the teeth in a helical pattern, while the helical rows are lined up parallelly. In addition to this, the cross helical gears have a point contact design and do not overlap. They can be either parallel or crossed. The helical gear motors can have any number of helical pairs, each with a different pitch circle diameter.
The benefits of the Parallel Shaft Helical Gearbox include high temperature and pressure handling. It is produced by skilled professionals using cutting-edge technology, and is widely recognized for its high performance. It is available in a range of technical specifications and is custom-made to suit individual requirements. These gearboxes are durable and low-noise and feature high reliability. You can expect to save up to 40% of your energy by using them.
The parallel shaft helical gear motors are designed to reduce the speed of a rotating part. The nodular cast iron housing helps make the unit robust in difficult environments, while the precision-machined gears provide quiet, vibration-free operation. These motors are available in double reduction, triple reduction, and quadruple reduction. The capacity ranges from 0.12 kW to 45 kW. You can choose from a wide variety of capacities, depending on the size of your gearing needs.
The SEW-EURODRIVE parallel shaft helical gearmotor is a convenient solution for space-constrained applications. The machine’s modular design allows for easy mounting and a wide range of ambient temperatures. They are ideal for a variety of mechanical applications, including conveyors, augers, and more. If you want a small footprint, the SEW-EURODRIVE parallel shaft helical gear motor is the best solution for you.
The parallel shaft helical gears are advantageous for both high and low speed applications. Parallel helical gears are also suitable for low speed and low duty applications. A good example of a cross-helix gear is the oil pump of an internal combustion engine. Both types of helical gears are highly reliable and offer vibration-free operation. They are more costly than conventional gear motors, but offer more durability and efficiency.
Helical gear unit
This helical gear unit is designed to operate under a variety of demanding conditions and can be used in a wide range of applications. Designed for long life and high torque density, this gear unit is available in a variety of torques and gear ratios. Its design and construction make it compatible with a wide range of critical mechanical systems. Common applications include conveyors, material handling, steel mills, and paper mills.
Designed for high-performance applications, the Heidrive helical gear unit provides superior performance and value. Its innovative design allows it to function well under a wide range of operating conditions and is highly resistant to damage. These gear motors can be easily combined with a helical gear unit. Their combined power output is 100 Nm, and they have a high efficiency of up to 90%. For more information about the helical gear motor, contact a Heidrive representative.
A helical gear unit can be classified by its reference section in the standard plane or the turning plane. Its center gap is the same as that of a spur gear, and its number of teeth is the same. In addition to this, the helical gear has a low axial thrust, which is another important characteristic. The helical gear unit is more efficient at transferring torque than a spur gear, and it is quieter, too.
These units are designed to handle large loads. Whether you are using them for conveyors, augers, or for any other application that involves high-speed motion, a helical gear unit will deliver maximum performance. A helical gear unit from Flender can handle 400,000 tasks with a high degree of reliability. Its high efficiency and high resistance to load ensures high plant availability. These gear motors are available in a variety of sizes, from single-speed to multi-speed.
PEC geared motors benefit from decades of design experience and high quality materials. They are robust, quiet, and offer excellent performance. They are available in multiple configurations and are dimensionally interchangeable with other major brands. The gear motors are manufactured as modular kits to minimize inventory. They can be fitted with additional components, such as backstops and fans. This makes it easy to customize your gear motors and save money while reducing costs.
Another type of helical gears is the double helical gear. The double helical gear unit has two helical faces with a gap between them. They are better for enclosed gear systems as they provide greater tooth overlap and smoother performance. Compared to double helical gears, they are smaller and more flexible than the Herringbone type. So, if you’re looking for a gear motor, a helical gear unit may be perfect for you.
editor by CX 2023-04-19
China Manufacturer 12v 24v 24 volt high power 100kg 5nm 50kg 50w 60 watt 70w torque 40rpm brush dc metal gear motor with brake dc motor
Guarantee: 3months-1year
Design Quantity: TJP60FR
Use: Residence Equipment, Beauty instrument, Intelligent Home, Industrial gear
Type: Gear MOTOR
Torque: 15 N.m
Construction: Long lasting Magnet
Commutation: Brush
Shield Characteristic: Drip-evidence
Speed(RPM): 5~1pcs.* Our guarantee interval is 1 calendar year.* We have 5 R&D engineers can supply you skilled remedies.* We have a aggressive price tag in Chinese market place, or even in the entire globe.* 10 to 40 days quick supply time foundation on various portions.* We have CE and ROHS certifications.* Our client provider staff will reply to you in 12 hrs. Firm Heritage Manufacturing facility Actual Landscape Item Certificates Buyers Opinions OEM & ODM CAD style: All components of dc equipment motor are made and drawn by our engineers. We use CAXA, NGWN to design various gears for our new goods. Solidworks is a skilled 3D modeling application, we will design motor components and employing 3D model for assembly verification. We have a demanding solution advancement process, the common solution improvement cycle in 40-60 times Packing and shipping and delivery 1. All get schedules are managed independently by each and every salesman 2. All components go by means of stringent quality inspection 3. All concluded products will be transported out soon after passing inspection china professional factory large precision solid iron V-belt AK collection mild responsibility bored to dimensions pulleys 4. All goods are packed in foam cartons: The sample shipping time of every single expresses are as follows(for example to the US): * DHL 7~12 work times * FedEx 6~9 function times * TNT 7~twelve work days * UPS 8~11 work times * EMS 10~18 operate times The shipping and delivery day of bulk items requirements certain negotiation. If the sample is delayed, we will notify you in progress and verify the new delivery time. FAQ Q: Are you buying and selling company or maker ?A: We are manufacturing facility.Q: How to purchase?A: Deliver us inquiry → Obtain our quotation → Negotiate details → Verify the sample → Sign contract/deposit → Mass creation → Cargo ready → Balance/delivery → More cooperationQ: How about Sample buy?A: Sample is available for you. you should make contact with us for details. When we demand you sample charge, please really feel effortless, it would be refund when you place official get.Q: Which transport way is accessible?A: DHL, UPS, FedEx, TNT, EMS, China Submit,Sea are accessible.The other delivery approaches are also obtainable, make sure you speak to us if you want ship by the other shipping and delivery way. Q: How prolonged is the produce[Creating] and shipping and delivery?A: Produce time is dependent on the amount you get. usually it requires 7-fifteen operating times.Q: My bundle has lacking goods. What can I do?A: Make sure you speak to our assistance crew and we will confirm your order with the deal contents.We apologize for any inconveniences. Q: How to confirm the payment?A: We settle for payment by T/T, PayPal, the other payment ways also could be accepted,You should get in touch with us just before you pay by the other payment methods. Also 30-fifty% deposit is obtainable, the equilibrium funds must be paid out prior to shipping and delivery.
| >>>>>>>>>>>>> LA-B11 IP54 Lower Sound Health-related Bed 100-240VAC24V-36VDC Dual Motor Actuator >Back to Homepage | ||||||||
The Basics of a Planetary Motor
A Planetary Motor is a type of gearmotor that uses multiple planetary gears to deliver torque. This system minimizes the chances of failure of individual gears and increases output capacity. Compared to the planetary motor, the spur gear motor is less complex and less expensive. However, a spur gear motor is generally more suitable for applications requiring low torque. This is because each gear is responsible for the entire load, limiting its torque.
Self-centering planetary gears
This self-centering mechanism for a planetary motor is based on a helical arrangement. The helical structure involves a sun-planet, with its crown and slope modified. The gears are mounted on a ring and share the load evenly. The helical arrangement can be either self-centering or self-resonant. This method is suited for both applications.
A helical planetary gear transmission is illustrated in FIG. 1. A helical configuration includes an output shaft 18 and a sun gear 18. The drive shaft extends through an opening in the cover to engage drive pins on the planet carriers. The drive shaft of the planetary gears can be fixed to the helical arrangement or can be removable. The transmission system is symmetrical, allowing the output shaft of the planetary motor to rotate radially in response to the forces acting on the planet gears.
A flexible pin can improve load sharing. This modification may decrease the face load distribution, but increases the (K_Hbeta) parameter. This effect affects the gear rating and life. It is important to understand the effects of flexible pins. It is worth noting that there are several other disadvantages of flexible pins in helical PGSs. The benefits of flexible pins are discussed below.
Using self-centering planetary gears for a helical planetary motor is essential for symmetrical force distribution. These gears ensure the symmetry of force distribution. They can also be used for self-centering applications. Self-centering planetary gears also guarantee the proper force distribution. They are used to drive a planetary motor. The gearhead is made of a ring gear, and the output shaft is supported by two ball bearings. Self-centering planetary gears can handle a high torque input, and can be suited for many applications.
To solve for a planetary gear mechanism, you need to find its pitch curve. The first step is to find the radius of the internal gear ring. A noncircular planetary gear mechanism should be able to satisfy constraints that can be complex and nonlinear. Using a computer, you can solve for these constraints by analyzing the profile of the planetary wheel’s tooth curve.
High torque
Compared to the conventional planetary motors, high-torque planetary motors have a higher output torque and better transmission efficiency. The high-torque planetary motors are designed to withstand large loads and are used in many types of applications, such as medical equipment and miniature consumer electronics. Their compact design makes them suitable for small space-saving applications. In addition, these motors are designed for high-speed operation.
They come with a variety of shaft configurations and have a wide range of price-performance ratios. The FAULHABER planetary gearboxes are made of plastic, resulting in a good price-performance ratio. In addition, plastic input stage gears are used in applications requiring high torques, and steel input stage gears are available for higher speeds. For difficult operating conditions, modified lubrication is available.
Various planetary gear motors are available in different sizes and power levels. Generally, planetary gear motors are made of steel, brass, or plastic, though some use plastic for their gears. Steel-cut gears are the most durable, and are ideal for applications that require a high amount of torque. Similarly, nickel-steel gears are more lubricated and can withstand a high amount of wear.
The output torque of a high-torque planetary gearbox depends on its rated input speed. Industrial-grade high-torque planetary gearboxes are capable of up to 18000 RPM. Their output torque is not higher than 2000 nm. They are also used in machines where a planet is decelerating. Their working temperature ranges between 25 and 100 degrees Celsius. For best results, it is best to choose the right size for the application.
A high-torque planetary gearbox is the most suitable type of high-torque planetary motor. It is important to determine the deceleration ratio before buying one. If there is no product catalog that matches your servo motor, consider buying a close-fitting high-torque planetary gearbox. There are also high-torque planetary gearboxes available for custom-made applications.
High efficiency
A planetary gearbox is a type of mechanical device that is used for high-torque transmission. This gearbox is made of multiple pairs of gears. Large gears on the output shaft mesh with small gears on the input shaft. The ratio between the big and small gear teeth determines the transmittable torque. High-efficiency planetary gearheads are available for linear motion, axial loads, and sterilizable applications.
The AG2400 high-end gear unit series is ideally matched to Beckhoff’s extensive line of servomotors and gearboxes. Its single-stage and multi-stage transmission ratios are highly flexible and can be matched to different robot types. Its modified lubrication helps it operate in difficult operating conditions. These high-performance gear units are available in a wide range of sizes.
A planetary gear motor can be made of steel, nickel-steel, or brass. In addition to steel, some models use plastic. The planetary gears share work between multiple gears, making it easy to transfer high amounts of power without putting a lot of stress on the gears. The gears in a planetary gear motor are held together by a movable arm. High-efficiency planetary gear motors are more efficient than traditional gearmotors.
While a planetary gear motor can generate torque, it is more efficient and cheaper to produce. The planetary gear system is designed with all gears operating in synchrony, minimizing the chance of a single gear failure. The efficiency of a planetary gearmotor makes it a popular choice for high-torque applications. This type of motor is suitable for many applications, and is less expensive than a standard geared motor.
The planetary gearbox is a combination of a planetary type gearbox and a DC motor. The planetary gearbox is compact, versatile, and efficient, and can be used in a wide range of industrial environments. The planetary gearbox with an HN210 DC motor is used in a 22mm OD, PPH, and ph configuration with voltage operating between 6V and 24V. It is available in many configurations and can be custom-made to meet your application requirements.
High cost
In general, planetary gearmotors are more expensive than other configurations of gearmotors. This is due to the complexity of their design, which involves the use of a central sun gear and a set of planetary gears which mesh with each other. The entire assembly is enclosed in a larger internal tooth gear. However, planetary motors are more effective for higher load requirements. The cost of planetary motors varies depending on the number of gears and the number of planetary gears in the system.
If you want to build a planetary gearbox, you can purchase a gearbox for the motor. These gearboxes are often available with several ratios, and you can use any one to create a custom ratio. The cost of a gearbox depends on how much power you want to move with the gearbox, and how much gear ratio you need. You can even contact your local FRC team to purchase a gearbox for the motor.
Gearboxes play a major role in determining the efficiency of a planetary gearmotor. The output shafts used for this type of motor are usually made of steel or nickel-steel, while those used in planetary gearboxes are made from brass or plastic. The former is the most durable and is best for applications that require high torque. The latter, however, is more absorbent and is better at holding lubricant.
Using a planetary gearbox will allow you to reduce the input power required for the stepper motor. However, this is not without its downsides. A planetary gearbox can also be replaced with a spare part. A planetary gearbox is inexpensive, and its spare parts are inexpensive. A planetary gearbox has low cost compared to a planetary motor. Its advantages make it more desirable in certain applications.
Another advantage of a planetary gear unit is the ability to handle ultra-low speeds. Using a planetary gearbox allows stepper motors to avoid resonance zones, which can cause them to crawl. In addition, the planetary gear unit allows for safe and efficient cleaning. So, whether you’re considering a planetary gear unit for a particular application, these gear units can help you get exactly what you need.
editor by czh 2023-02-20
China 22mm 12V 24V High Torque DC Planetary Gear Motor for Smart Door Lock wholesaler
Solution Description
Note:
22mm 12V 24V Large Torque DC Planetary Equipment Motor for Smart door lock
Major rewards:
1. Motor specs this sort of as voltage, velocity, torque, the shaft, packing can be tailored.
2. As a gear reduction motor, it is really ideal for software that calls for lower rpm and substantial torque
3. Large sealing: the output component is geared up with an oil seal and O-ring, which can stop the lubrication grease backflow in the gearbox, and stay away from the aging or hurt of oil seal insulation.
4. Substantial efficiency: making use of a new pressed silicon steel sheet, high precision main, strong magnetic permeability. The profile uses the new warmth dissipation structure.
5. Applicability: Compact size, suited for numerous working environments.
Planetary gearbox positive aspects:
1) Low velocity: 12 – 1650 rpm.
2) High torque: .05 kg.cm to 5 kg.cm.
three) Tiny vibration, reduced sounds, reduced power intake.
Application:
DC miniature Planetary Gear Motor widely used in business office automation, intelligence home furniture, manufacturing automation, health-related tools, monetary equipment and match equipment sectors, these kinds of as automated window opener, glass curtain wall, car curtain, financial institution ATM, automated funds register, note vending device, phase limelight, and other computerized products.
Drawing:
| Sort | Ratio | one: 3.4 | one: six | 1: fourteen | one: 23 | one: 33 | 1: fifty one | one: 86 | 1: 111 | one: a hundred ninety | 1: 246 | one: 315 | one: 531 | 1: 707 | one: 913 | one: 1180 | 1: 1525 | 1: 1972 | |
| D223 | Rated torque | kg. cm | .05 | .07 | .fifteen | .25 | .36 | .five | .8 | one | one.seven | two | three | five | five | six | six | six | six |
| Rated speed | rpm | 1650 | 1100 | 471 | 287 | two hundred | 129 | seventy seven | fifty nine | 35 | 27 | 21 | twelve | 9 | seven | six | 4 | 3 | |
| Gearbox | Instantaneous torque |
Kg. cm | 3 | 4 | 5 | 7 | 8 | ||||||||||||
| Allowable torque |
Kg. cm | 2 | 3 | 4 | 5 | 6 | |||||||||||||
| Size | mm | 18.1 | 23.4 | 28.seven | 34 | 39.3 | |||||||||||||
| Backlash | O | 0.five | 0.6 | 0.8 | 1 | 1.5 | |||||||||||||
| Excess weight | g | 40 | 55.two | 68.2 | 84.2 | 96.two | |||||||||||||
About Us:
I.CH was founded in 2006, found in HangZhou. We specialised in exploring, developing, and servicing electrical motors, gearbox, and higher precision gears with the modest module. Following a long time of advancement, we have an independent merchandise layout and R&D group, support crew, and a expert high quality manage staff. To realize our service concept much better, supply higher-quality merchandise and exceptional services, we have been fully commited to the main capacity and instruction. We have a holding manufacturing unit in HangZhou, which creates higher precision small mould gears, gear shaft, gearbox, and planetary gearbox assembling.
Our Product:
DC Gear DC Planetary Gear Spur Gearbox
Spur Equipment Helical Gear
Our Certificate:
As we all know, the accomplishment of the organization is primarily based on the good quality of the motor. So, to get the acknowledgment in the marketplace, we get ROHS, CE, ISO900 certificates.
Function-flow:
Provider:
ODM & OEM
Gearbox style and development
Package&Ship:
Carton, pallet, or what you want
The delivery time is about thirty-45 days.
Customer’s Going to:
FAQ:
one. Can you custom gearbox?
Sure. The requirements can be developed according to the customer’s needs.
2. DO you offer the sample?
Indeed.
3. Do you supply complex help?
Yes.we have an impartial solution style and R&D crew, provider group and expert top quality management staff.
4. Do you have a factory?
Of course, we are a expert producer.
5. Can I arrive to your organization to pay a visit to?
Of course
Associated Products:
|
US $3 / Piece | |
1 Piece (Min. Order) |
###
| Size: | 22mm |
|---|---|
| Rated Torque: | 0.05kg.Cm-6kg.Cm |
| Rated Speed: | 1650rpm-3rpm |
| Length: | 18.1mm-39.3mm |
| Ratio: | 1:3.4-1:1972 |
| Allowable Torque: | 2kg.Cm-6kg.Cm |
###
| Customization: |
Available
|
|---|
###
| Type | Ratio | 1: 3.4 | 1: 6 | 1: 14 | 1: 23 | 1: 33 | 1: 51 | 1: 86 | 1: 111 | 1: 190 | 1: 246 | 1: 315 | 1: 531 | 1: 707 | 1: 913 | 1: 1180 | 1: 1525 | 1: 1972 | |
| D223 | Rated torque | kg. cm | 0.05 | 0.07 | 0.15 | 0.25 | 0.36 | 0.5 | 0.8 | 1 | 1.7 | 2 | 3 | 5 | 5 | 6 | 6 | 6 | 6 |
| Rated speed | rpm | 1650 | 1100 | 471 | 287 | 200 | 129 | 77 | 59 | 35 | 27 | 21 | 12 | 9 | 7 | 6 | 4 | 3 | |
| Gearbox | Instantaneous torque |
Kg. cm | 3 | 4 | 5 | 7 | 8 | ||||||||||||
| Allowable torque |
Kg. cm | 2 | 3 | 4 | 5 | 6 | |||||||||||||
| Length | mm | 18.1 | 23.4 | 28.7 | 34 | 39.3 | |||||||||||||
| Backlash | O | 0.5 | 0.6 | 0.8 | 1 | 1.5 | |||||||||||||
| Weight | g | 40 | 55.2 | 68.2 | 84.2 | 96.2 | |||||||||||||
|
US $3 / Piece | |
1 Piece (Min. Order) |
###
| Size: | 22mm |
|---|---|
| Rated Torque: | 0.05kg.Cm-6kg.Cm |
| Rated Speed: | 1650rpm-3rpm |
| Length: | 18.1mm-39.3mm |
| Ratio: | 1:3.4-1:1972 |
| Allowable Torque: | 2kg.Cm-6kg.Cm |
###
| Customization: |
Available
|
|---|
###
| Type | Ratio | 1: 3.4 | 1: 6 | 1: 14 | 1: 23 | 1: 33 | 1: 51 | 1: 86 | 1: 111 | 1: 190 | 1: 246 | 1: 315 | 1: 531 | 1: 707 | 1: 913 | 1: 1180 | 1: 1525 | 1: 1972 | |
| D223 | Rated torque | kg. cm | 0.05 | 0.07 | 0.15 | 0.25 | 0.36 | 0.5 | 0.8 | 1 | 1.7 | 2 | 3 | 5 | 5 | 6 | 6 | 6 | 6 |
| Rated speed | rpm | 1650 | 1100 | 471 | 287 | 200 | 129 | 77 | 59 | 35 | 27 | 21 | 12 | 9 | 7 | 6 | 4 | 3 | |
| Gearbox | Instantaneous torque |
Kg. cm | 3 | 4 | 5 | 7 | 8 | ||||||||||||
| Allowable torque |
Kg. cm | 2 | 3 | 4 | 5 | 6 | |||||||||||||
| Length | mm | 18.1 | 23.4 | 28.7 | 34 | 39.3 | |||||||||||||
| Backlash | O | 0.5 | 0.6 | 0.8 | 1 | 1.5 | |||||||||||||
| Weight | g | 40 | 55.2 | 68.2 | 84.2 | 96.2 | |||||||||||||
The Benefits of Using a Gear Motor
A gear motor works on the principle of conservation of angular momentum. As the smaller gear covers more RPM and the larger gear produces more torque, the ratio between the two is greater than one. Similarly, a multiple gear motor follows the principle of energy conservation, with the direction of rotation always opposite to the one that is adjacent to it. It’s easy to understand the concept behind gear motors and the various types available. Read on to learn about the different types of gears and their applications.
Electric motor
The choice of an electric motor for gear motor is largely dependent on the application. There are various motor and gearhead combinations available, and some are more efficient than others. However, it is critical to understand the application requirements and select a motor that meets these needs. In this article, we’ll examine some of the benefits of using a gear motor. The pros and cons of each type are briefly discussed. You can buy new gear motors at competitive prices, but they aren’t the most reliable or durable option for your application.
To determine which motor is best for your application, you’ll need to consider the load and speed requirements. A gear motor’s efficiency (e) can be calculated by taking the input and output values and calculating their relation. On the graph below, the input (T) and output (P) values are represented as dashed lines. The input (I) value is represented as the torque applied to the motor shaft. The output (P) is the amount of mechanical energy converted. A DC gear motor is 70% efficient at 3.75 lb-in / 2,100 rpm.
In addition to the worm gear motor, you can also choose a compact DC worm gear motor with a variable gear ratio from 7.5 to 80. It has a range of options and can be custom-made for your specific application. The 3-phase AC gear motor, on the other hand, works at a rated power of one hp and torque of 1.143.2 kg-m. The output voltage is typically 220V.
Another important factor is the output shaft orientation. There are two main orientations for gearmotors: in-line and offset. In-line output shafts are most ideal for applications with high torque and short reduction ratios. If you want to avoid backlash, choose a right angle output shaft. An offset shaft can cause the output shaft to become excessively hot. If the output shaft is angled at a certain angle, it may be too large or too small.
Gear reducer
A gear reducer is a special kind of speed reducing motor, usually used in large machinery, such as compressors. These reducers have no cooling fan and are not designed to handle heavy loads. Different purposes require different service factors. For instance, a machine that requires frequent fast accelerations and occasional load spikes needs a gear reducer with a high service factor. A gear reducer that’s designed for long production shifts should be larger than a machine that uses it for short periods of time.
A gear reducer can reduce the speed of a motor by a factor of two. The reduction ratio changes the rotation speed of the receiving member. This change in speed is often required to solve problems of inertia mismatch. The torque density of a gear reducer is measured in newton meters and will depend on the motor used. The first criterion is the configuration of the input and output shafts. A gear ratio of 2:1, for example, means that the output speed has been cut in half.
Bevel gear reducers are a good option if the input and output shafts are perpendicular. This type is very robust and is perfect for situations where the angle between two axes is small. However, bevel gear reducers are expensive and require constant maintenance. They are usually used in heavy-duty conveyors and farm equipment. The correct choice of gear reducer for gear motor is crucial for the efficiency and reliability of the mechanism. To get the best gear reducer for your application, talk to a qualified manufacturer today.
Choosing a gear reducer for a gear motor can be tricky. The wrong one can ruin an entire machine, so it’s important to know the specifics. You must know the torque and speed requirements and choose a motor with the appropriate ratio. A gear reducer should also be compatible with the motor it’s intended for. In some cases, a smaller motor with a gear reducer will work better than a larger one.
Motor shaft
Proper alignment of the motor shaft can greatly improve the performance and life span of rotating devices. The proper alignment of motors and driven instruments enhances the transfer of energy from the motor to the instrument. Incorrect alignment leads to additional noise and vibration. It may also lead to premature failure of couplings and bearings. Misalignment also results in increased shaft and coupling temperatures. Hence, proper alignment is critical to improve the efficiency of the driven instrument.
When choosing the correct type of gear train for your motor, you need to consider its energy efficiency and the torque it can handle. A helical geared motor is more efficient for high output torque applications. Depending on the required speed and torque, you can choose between an in-line and a parallel helical geared motor. Both types of gears have their advantages and disadvantages. Spur gears are widespread. They are toothed and run parallel to the motor shaft.
A planetary gear motor can also have a linear output shaft. A stepping motor should not operate at too high current to prevent demagnetization, which will lead to step loss or torque drop. Ensure that the motor and gearbox output shafts are protected from external impacts. If the motor and gearbox are not protected against bumps, they may cause thread defects. Make sure that the motor shafts and rotors are protected from external impacts.
When choosing a metal for your gear motor’s motor shaft, you should consider the cost of hot-rolled bar stock. Its outer layers are more difficult to machine. This type of material contains residual stresses and other problems that make it difficult to machine. For these applications, you should choose a high-strength steel with hard outer layers. This type of steel is cheaper, but it also has size considerations. It’s best to test each material first to determine which one suits your needs.
In addition to reducing the speed of your device, a geared motor also minimizes the torque generated by your machine. It can be used with both AC and DC power. A high-quality gear motor is vital for stirring mechanisms and conveyor belts. However, you should choose a geared motor that uses high-grade gears and provides maximum efficiency. There are many types of planetary gear motors and gears on the market, and it’s important to choose the right one.
First stage gears
The first stage gears of a gear motor are the most important components of the entire device. The motor’s power transmission is 90% efficient, but there are many factors that can affect its performance. The gear ratios used should be high enough to handle the load, but not too high that they are limiting the motor’s speed. A gear motor should also have a healthy safety factor, and the lubricant must be sufficient to overcome any of these factors.
The transmission torque of the gear changes with its speed. The transmission torque at the input side of the gear decreases, transferring a small torque to the output side. The number of teeth and the pitch circle diameters can be used to calculate the torque. The first stage gears of gear motors can be categorized as spur gears, helical gears, or worm gears. These three types of gears have different torque capacities.
The first stage helical gear is the most important part of a gear motor. Its function is to transfer rotation from one gear to the other. Its output is the gearhead. The second stage gears are connected by a carrier. They work in tandem with the first stage gear to provide the output of the gearhead. Moreover, the first stage carrier rotates in the same direction as the input pinion.
Another important component is the output torque of the gearmotor. When choosing a gearmotor, consider the starting torque, running torque, output speed, overhung and shock loads, duty cycles, and more. It is crucial to choose a gearmotor with the right ratio for the application. By choosing the proper gearmotor, you will get maximum performance with minimal operating costs and increase plant productivity. For more information on first stage gears, check out our blog.
The first stage of a gear motor is composed of a set of fixed and rotating sprockets. The first stage of these gears acts as a drive gear. Its rotational mass is a limiting factor for torque. The second stage consists of a rotating shaft. This shaft rotates in the direction of the torque axis. It is also the limiting force for the motor’s torque.
editor by czh 2023-01-03
China Reverse Adjustable Good Quality 52mm 35.1W Food Waste Disposal High Torque 12V Forklift Car Brushed DC Planetary Gear Motor Electric Motor with Best Sales
Merchandise Description
| BG 52ZYT DC Brushed Motor | |
| Environmental Conditons | -20ºC~50ºC |
| Lnsulation Clase | B |
| Security course | IP44 |
| Noise | ≤65dB |
| Number of phases | Single |
| Lifespan | >1000h |
| Electrical Requirements | |||||||||
| Model | RATED LOAD | NO LOAD | STALL | ||||||
| Voltage | Power |
Speed |
Torque | Current | Speed | Current | Torque | Current | |
| V | W | rpm | N.m | A | rpm | A | N.m | A | |
| BG 52ZYT01 | twelve | 35.1 | 2550 | .thirteen | 5 | 3000 | .65 | 0.sixty four | 21.one |
| BG 52ZYT02 | 24 | 44.eight | 2600 | .sixteen | two.8 | 3000 | .32 | 0.87 | thirteen.8 |
| We can also customize products according to customer demands . | |||||||||
| Planetary Equipment Motor Specialized Data-BG | ||||||||
| Ratio | ten.2 | 19.2 | 26.9 | 188 | 264 | 721 | 669 | 1911 |
| NO-load pace | 1167 | 700 | 437 | 175 | ninety eight | 87.5 | 58 | 36 |
| Rated velocity(rpm) | one thousand | 600 | 375 | 150 | eighty three | 75 | fifty | 31 |
| Rated torque | one.one | 2.one | 2.ninety seven | 18.three | 25 | 25 | 25 | 25 |
Recognized in 1994, HangZhou BG Motor Factory is a specialist maker of brushless DC motors, brushed DC motors, planetary gear motors, worm gear motors, Common motors and AC motors. We have a plant area of 6000 sq. meters, numerous patent certificates, and we have the independent design and improvement abilities and robust specialized force, with an yearly output of a lot more than 1 million units. Given that the commencing of its establishment, BG motor has targeted on the general resolution of motors. We manufacture and design and style motors, provide expert tailored solutions, respond swiftly to client demands, and actively aid consumers to resolve problems. Our motor items are exported to 20 nations, such as the United States, Germany, Italy, the United Kingdom, Poland, Slovenia, Switzerland, Sweden, Singapore, South Korea and so on.
Our founder, Mr. Sun, has far more than forty many years of knowledge in motor technological innovation, and our other engineers also have far more than fifteen many years of expertise, and sixty% of our staff have far more than 10 many years of expertise, and we can assure you that the quality of our motors is prime notch.
The products cover AGV, underwater robots, robots, stitching equipment industry, vehicles, health-related gear, automated doorways, lifting gear, industrial equipment and have a vast range of purposes.
We attempt for CZPT in the top quality of every single product, and we are only a modest and refined company.
Our vision: Generate the globe ahead and make existence far better!
Q:1.What sort of motors can you give?
A:At existing, we primarily make brushless DC motors, brush DC motors, AC motors, Universal Motors the power of the motor is significantly less than 5000W, and the diameter of the motor is not far more than 200mm
Q:2.Can you send me a value list?
A:For all of our motors, they are custom-made dependent on various needs like lifetime, noise,voltage,and shaft and many others. The cost also differs according to once-a-year amount. So it is actually difficult for us to offer a price tag list. If you can share your comprehensive needs and once-a-year quantity, we’ll see what offer you we can supply.
Q:3.Can l get some samples?
A:It is dependent. If only a few samples for private use or alternative, I am frightened it’ll be difficult for us to offer because all of our motors are personalized created and no stock available if there are no even more demands. If just sample tests ahead of the official get and our MOQ,price and other terms are suitable,we’d enjoy to supply samples.
This fall:Can you give OEM or ODM provider?
A:Yes,OEM and ODM are both available, we have the expert R&D dept which can provide professional answers for you.
Q5:Can l check out your manufacturing facility before we location an get?
A:welcome to visit our manufacturing unit,use each and every happy if we have the likelihood to know every single other far more.
Q:6.What is actually the guide time for a standard get?
A:For orders, the standard guide time is fifteen-20 days and this time can be shorter or for a longer time primarily based on the different model,period of time and quantity.
| Application: | Universal, Industrial, Household Appliances, Car, Power Tools, Robot Arm |
|---|---|
| Operating Speed: | Low Speed |
| Excitation Mode: | DC |
| Function: | Driving |
| Casing Protection: | Closed Type |
| Number of Poles: | Can Be Choosen |
###
| Samples: |
US$ 0/Piece
1 Piece(Min.Order) |
|---|
###
| Customization: |
Available
|
|---|
###
| BG 52ZYT DC Brushed Motor | |
| Environmental Conditons | -20ºC~50ºC |
| Lnsulation Clase | B |
| Protection class | IP44 |
| Noise | ≤65dB |
| Number of phases | Single |
| Lifespan | >1000h |
###
| Electrical Specifications | |||||||||
| Model | RATED LOAD | NO LOAD | STALL | ||||||
| Voltage | Power |
Speed |
Torque | Current | Speed | Current | Torque | Current | |
| V | W | rpm | N.m | A | rpm | A | N.m | A | |
| BG 52ZYT01 | 12 | 35.1 | 2550 | 0.13 | 5 | 3000 | 0.65 | 0.64 | 21.1 |
| BG 52ZYT02 | 24 | 44.8 | 2600 | 0.16 | 2.8 | 3000 | 0.32 | 0.87 | 13.8 |
| We can also customize products according to customer requirements . | |||||||||
###
| Planetary Gear Motor Technical Data-BG | ||||||||
| Ratio | 10.2 | 19.2 | 26.9 | 188 | 264 | 721 | 669 | 1911 |
| NO-load speed | 1167 | 700 | 437 | 175 | 98 | 87.5 | 58 | 36 |
| Rated speed(rpm) | 1000 | 600 | 375 | 150 | 83 | 75 | 50 | 31 |
| Rated torque | 1.1 | 2.1 | 2.97 | 18.3 | 25 | 25 | 25 | 25 |
| Application: | Universal, Industrial, Household Appliances, Car, Power Tools, Robot Arm |
|---|---|
| Operating Speed: | Low Speed |
| Excitation Mode: | DC |
| Function: | Driving |
| Casing Protection: | Closed Type |
| Number of Poles: | Can Be Choosen |
###
| Samples: |
US$ 0/Piece
1 Piece(Min.Order) |
|---|
###
| Customization: |
Available
|
|---|
###
| BG 52ZYT DC Brushed Motor | |
| Environmental Conditons | -20ºC~50ºC |
| Lnsulation Clase | B |
| Protection class | IP44 |
| Noise | ≤65dB |
| Number of phases | Single |
| Lifespan | >1000h |
###
| Electrical Specifications | |||||||||
| Model | RATED LOAD | NO LOAD | STALL | ||||||
| Voltage | Power |
Speed |
Torque | Current | Speed | Current | Torque | Current | |
| V | W | rpm | N.m | A | rpm | A | N.m | A | |
| BG 52ZYT01 | 12 | 35.1 | 2550 | 0.13 | 5 | 3000 | 0.65 | 0.64 | 21.1 |
| BG 52ZYT02 | 24 | 44.8 | 2600 | 0.16 | 2.8 | 3000 | 0.32 | 0.87 | 13.8 |
| We can also customize products according to customer requirements . | |||||||||
###
| Planetary Gear Motor Technical Data-BG | ||||||||
| Ratio | 10.2 | 19.2 | 26.9 | 188 | 264 | 721 | 669 | 1911 |
| NO-load speed | 1167 | 700 | 437 | 175 | 98 | 87.5 | 58 | 36 |
| Rated speed(rpm) | 1000 | 600 | 375 | 150 | 83 | 75 | 50 | 31 |
| Rated torque | 1.1 | 2.1 | 2.97 | 18.3 | 25 | 25 | 25 | 25 |
The Benefits of Using a Gear Motor
A gear motor works on the principle of conservation of angular momentum. As the smaller gear covers more RPM and the larger gear produces more torque, the ratio between the two is greater than one. Similarly, a multiple gear motor follows the principle of energy conservation, with the direction of rotation always opposite to the one that is adjacent to it. It’s easy to understand the concept behind gear motors and the various types available. Read on to learn about the different types of gears and their applications.
Electric motor
The choice of an electric motor for gear motor is largely dependent on the application. There are various motor and gearhead combinations available, and some are more efficient than others. However, it is critical to understand the application requirements and select a motor that meets these needs. In this article, we’ll examine some of the benefits of using a gear motor. The pros and cons of each type are briefly discussed. You can buy new gear motors at competitive prices, but they aren’t the most reliable or durable option for your application.
To determine which motor is best for your application, you’ll need to consider the load and speed requirements. A gear motor’s efficiency (e) can be calculated by taking the input and output values and calculating their relation. On the graph below, the input (T) and output (P) values are represented as dashed lines. The input (I) value is represented as the torque applied to the motor shaft. The output (P) is the amount of mechanical energy converted. A DC gear motor is 70% efficient at 3.75 lb-in / 2,100 rpm.
In addition to the worm gear motor, you can also choose a compact DC worm gear motor with a variable gear ratio from 7.5 to 80. It has a range of options and can be custom-made for your specific application. The 3-phase AC gear motor, on the other hand, works at a rated power of one hp and torque of 1.143.2 kg-m. The output voltage is typically 220V.
Another important factor is the output shaft orientation. There are two main orientations for gearmotors: in-line and offset. In-line output shafts are most ideal for applications with high torque and short reduction ratios. If you want to avoid backlash, choose a right angle output shaft. An offset shaft can cause the output shaft to become excessively hot. If the output shaft is angled at a certain angle, it may be too large or too small.
Gear reducer
A gear reducer is a special kind of speed reducing motor, usually used in large machinery, such as compressors. These reducers have no cooling fan and are not designed to handle heavy loads. Different purposes require different service factors. For instance, a machine that requires frequent fast accelerations and occasional load spikes needs a gear reducer with a high service factor. A gear reducer that’s designed for long production shifts should be larger than a machine that uses it for short periods of time.
A gear reducer can reduce the speed of a motor by a factor of two. The reduction ratio changes the rotation speed of the receiving member. This change in speed is often required to solve problems of inertia mismatch. The torque density of a gear reducer is measured in newton meters and will depend on the motor used. The first criterion is the configuration of the input and output shafts. A gear ratio of 2:1, for example, means that the output speed has been cut in half.
Bevel gear reducers are a good option if the input and output shafts are perpendicular. This type is very robust and is perfect for situations where the angle between two axes is small. However, bevel gear reducers are expensive and require constant maintenance. They are usually used in heavy-duty conveyors and farm equipment. The correct choice of gear reducer for gear motor is crucial for the efficiency and reliability of the mechanism. To get the best gear reducer for your application, talk to a qualified manufacturer today.
Choosing a gear reducer for a gear motor can be tricky. The wrong one can ruin an entire machine, so it’s important to know the specifics. You must know the torque and speed requirements and choose a motor with the appropriate ratio. A gear reducer should also be compatible with the motor it’s intended for. In some cases, a smaller motor with a gear reducer will work better than a larger one.
Motor shaft
Proper alignment of the motor shaft can greatly improve the performance and life span of rotating devices. The proper alignment of motors and driven instruments enhances the transfer of energy from the motor to the instrument. Incorrect alignment leads to additional noise and vibration. It may also lead to premature failure of couplings and bearings. Misalignment also results in increased shaft and coupling temperatures. Hence, proper alignment is critical to improve the efficiency of the driven instrument.
When choosing the correct type of gear train for your motor, you need to consider its energy efficiency and the torque it can handle. A helical geared motor is more efficient for high output torque applications. Depending on the required speed and torque, you can choose between an in-line and a parallel helical geared motor. Both types of gears have their advantages and disadvantages. Spur gears are widespread. They are toothed and run parallel to the motor shaft.
A planetary gear motor can also have a linear output shaft. A stepping motor should not operate at too high current to prevent demagnetization, which will lead to step loss or torque drop. Ensure that the motor and gearbox output shafts are protected from external impacts. If the motor and gearbox are not protected against bumps, they may cause thread defects. Make sure that the motor shafts and rotors are protected from external impacts.
When choosing a metal for your gear motor’s motor shaft, you should consider the cost of hot-rolled bar stock. Its outer layers are more difficult to machine. This type of material contains residual stresses and other problems that make it difficult to machine. For these applications, you should choose a high-strength steel with hard outer layers. This type of steel is cheaper, but it also has size considerations. It’s best to test each material first to determine which one suits your needs.
In addition to reducing the speed of your device, a geared motor also minimizes the torque generated by your machine. It can be used with both AC and DC power. A high-quality gear motor is vital for stirring mechanisms and conveyor belts. However, you should choose a geared motor that uses high-grade gears and provides maximum efficiency. There are many types of planetary gear motors and gears on the market, and it’s important to choose the right one.
First stage gears
The first stage gears of a gear motor are the most important components of the entire device. The motor’s power transmission is 90% efficient, but there are many factors that can affect its performance. The gear ratios used should be high enough to handle the load, but not too high that they are limiting the motor’s speed. A gear motor should also have a healthy safety factor, and the lubricant must be sufficient to overcome any of these factors.
The transmission torque of the gear changes with its speed. The transmission torque at the input side of the gear decreases, transferring a small torque to the output side. The number of teeth and the pitch circle diameters can be used to calculate the torque. The first stage gears of gear motors can be categorized as spur gears, helical gears, or worm gears. These three types of gears have different torque capacities.
The first stage helical gear is the most important part of a gear motor. Its function is to transfer rotation from one gear to the other. Its output is the gearhead. The second stage gears are connected by a carrier. They work in tandem with the first stage gear to provide the output of the gearhead. Moreover, the first stage carrier rotates in the same direction as the input pinion.
Another important component is the output torque of the gearmotor. When choosing a gearmotor, consider the starting torque, running torque, output speed, overhung and shock loads, duty cycles, and more. It is crucial to choose a gearmotor with the right ratio for the application. By choosing the proper gearmotor, you will get maximum performance with minimal operating costs and increase plant productivity. For more information on first stage gears, check out our blog.
The first stage of a gear motor is composed of a set of fixed and rotating sprockets. The first stage of these gears acts as a drive gear. Its rotational mass is a limiting factor for torque. The second stage consists of a rotating shaft. This shaft rotates in the direction of the torque axis. It is also the limiting force for the motor’s torque.
editor by czh 2023-01-02
China 12V 24V 36mm Low Noise Small High Torque DC Planetary Gear Motor with Encoders for Automobile Power Tailgate with Hot selling
Solution Description
10mm 3V Large Precision CCTV Camera Geared Motor With Gearbox
Solution Parameters
Model: ZWBMD571571-168
- Rated Voltage: 3.0V
- No Load Speed: 98 rpm
- No Load Current: 80mA
- Rated Load Speed: 86 rpm
- Rated Load Current: 220mA
- Rated Load Torque: 106 gf.cm
- Rated Torque of Equipment Box: 2,000 gf.cm
- Immediate Torque of Equipment Box: 6,000 gf.cm
- General Length L: 34 mm
- Gear Box Size L1: 19 mm
| Design | Application Parameters | Rated Torque of Gear Box | Instant Torque of Gear Box | Gear Ratio | Gear Box Length L1 |
|||||||
| Rated | At No Load | At Rated Load | Overall Duration L |
|||||||||
| Voltage | Pace | Existing | Velocity | Recent | Torque | |||||||
| VDC | rpm | mA | rpm | mA | gf.cm | mN.m | mm | gf.cm | gf.cm | mm | ||
| ZWBMD571571-forty six | 3. | 375 | 80 | 315 | 215 | 39 | three.8 | 30.9 | 2000 | 6000 | forty six | 15.9 |
| ZWBMD571571-sixty nine | three. | 250 | eighty | 210 | 215 | 58 | 5.seven | 2000 | 6000 | sixty nine | ||
| ZWBMD571571-102 | three. | 169 | 80 | 142 | 215 | 86 | 8.four | 2000 | 6000 | 102 | ||
| ZWBMD571571-151 | three. | 114 | eighty | 96 | 215 | 127 | twelve.5 | 2000 | 6000 | 151 | ||
| ZWBMD571571-168 | 3. | 98 | 80 | 86 | 220 | 106 | 10.4 | 34 | 2000 | 6000 | 168 | 19 |
| ZWBMD571571-249 | three. | 66 | 80 | 58 | 220 | 158 | 15 | 2000 | 6000 | 249 | ||
| ZWBMD571571-368 | three. | 45 | eighty | 39 | 220 | 233 | 23 | 2000 | 6000 | 368 | ||
| ZWBMD571571-546 | 3. | thirty | eighty | 27 | 220 | 346 | 34 | 2000 | 6000 | 546 | ||
| ZWBMD571571-809 | three. | 20 | eighty | 18 | 220 | 512 | fifty | 2000 | 6000 | 809 | ||
above requirements just for reference and customizable according to specifications.
Make sure you let us know your needs and we will offer you with micro transmission options.
In depth Photographs
Application
| Intelligent wearable devices | watch,VR,AR,XR and and so on. |
| Home application | kitchen area appliances, stitching equipment, corn popper, vacuum cleaner, backyard garden instrument, sanitary ware, window curtain, clever closestool, sweeping robotic, power seat, standing desk, electric sofa, Television, computer, treadmill, spyhole, cooker hood, electrical drawer, electric mosquito net, smart cupboard, smart wardrobe, automated cleaning soap dispenser, UV baby bottle sterilizer, lifting scorching pot cookware, dishwasher, washing equipment, meals breaking device, dryer, air conditioning, dustbin, espresso machine, whisk,wise lock,bread maker,Window cleansing robot and and so forth. |
| conversation equipment | 5G base station,online video convention,cell mobile phone and and so forth. |
| Place of work automation equipments | scanners, printers, multifunction equipment duplicate equipment, fax (FAX paper cutter), pc peripheral, bank equipment, display screen, lifting socket, show,notebook Laptop and etc. |
| Automotive products | conditioning damper actuator, automobile DVD,doorway lock actuator, retractable rearview mirror, meters, optic axis manage gadget, head light-weight beam amount adjuster, auto h2o pump, car antenna, lumbar support, EPB, car tail gate electrical putter, HUD, head-up screen, automobile sunroof, EPS, AGS, car window, head restraint, E-booster, vehicle seat, motor vehicle charging station and and many others. |
| Toys and models | radio control model, automated cruise control, journey-on toy, academic robotic, programming robot, medical robotic, automated feeder, intelligent creating blocks, escort robotic and and so forth. |
| Healthcare equipments | blood pressure meter, breath device, healthcare cleaning pump, health-related bed, blood force monitors, medical ventilator, surgical staplers, infusion pump, dental instrument, self-clotting cutter, wound cleaning pump for orthopedic surgical treatment,electronic cigarette, eyebrow pencil,fascia gun, , surgical robotic,laboratory automation and and so forth. |
| Industrials | flow manage valves, seismic tests,automated reclosing,Agricultural unmanned aerial car,automatic feeder ,intelligent express cabinet and etc. |
| Electric power tools | electric powered drill, screwdriver,garden instrument and and so on. |
| Precision instruments | optics instruments,automated vending equipment, wire-stripping equipment and etc. |
| Private treatment | tooth brush, hair clipper, electric shaver, massager, vibrator, hair dryer, rubdown machine, scissor hair machine, foot grinder,anti-myopia pen, facial attractiveness products, hair roller,Electric powered threading knife,Electricity Ideal PORE, Puff device,eyebrow tweezers and and many others. |
| Buyer electronics | digital camera, cellular mobile phone,digital digicam, automated retracting system,camcorder, kinescope DVD,headphone stereo, cassette tape recorder, bluetooth earbud charging case, turntable, pill,UAV(unmanned aerial vehicle),surveillance digicam,PTZ camera, rotating sensible speaker and and many others. |
| robots | instructional robotic, programming robotic, medical robot, escort robot and and so on. |
Company Profile
HangZhou CZPT Equipment & Electronics Co., Ltd was proven in 2001,We give the complete push resolution for clients from design and style, tooling fabrication, factors manufacturing and assembly.
Workshop
Screening Products
one) Competitive Rewards
- 1) Competitive Positive aspects
19+calendar year encounter in production motor gearbox
We give complex support from r&d, prototype, screening, assembly and serial creation , ODM &OEM
Competitive Price
Solution Overall performance: Minimal noise, Substantial performance, Prolonged lifespan
Prompt Supply: 15 working days right after payment
Small Orders Acknowledged
2) Main Items
-
Precision reduction gearbox and its diameter:3.4mm-38mm,voltage:1.5-24V,electrical power: .01-40W,output speed:5-2000rpm and output torque:1. gf.cm -50kgf.cm,
- Personalized worm and gear transmission machinery
- Exact electromechanical movement module
- Precise part and assembly of plastic and metal powder injection.
Our Services
- ODM & OEM
- Gearbox layout and growth
- Associated engineering help
- Micro generate gearbox custom resolution
Packaging & Delivery
1) Packing Information
packed in nylon to start with, then carton, and then strengthened with wood situation for outer packing.
Or according to client’s requirement.
two) Delivery Specifics
samples will be shipped in ten times
batch order foremost time in accordance to the actual predicament.
Certifications
Certifications
We Have passed to keep ISO9001:2015(CN11/3571),ISO14001:2004(U006616E0153R3M), ISO13485:2016(CN18/42018) and IATF16949:2016(CN11/3571.01).
and far more…
FAQ
FAQ
one. Can you make the gearbox with custom technical specs?
Sure. We have design and growth staff, also a fantastic phrase of engineers, each of them have
numerous operate years expertise.
two.Do you supply the samples?
Sure. Our firm can supply the samples to you, and the shipping time is about 5-15days according to the specification of gearbox you want.
3.What is your MOQ?
Our MOQ is 2000pcs. But at the beginning of our enterprise, we settle for little buy.
4. Do you have the merchandise in stock?
I am sorry we donot have the product in inventory, All merchandise are created with orders.
5. Do you supply technologies support?
Yes. Our business have design and growth group, we can offer technologies help if you
need.
six.How to ship to us?
We will ship the products to you in accordance to the DHL or UPS or FEDEX and so on account you give.
7.How to pay the income?
We acknowledge T/T in advance. Also we have different financial institution account for obtaining income, like US dollors or RMB and so forth.
eight. How can I know the item is suitable for me?
Frist, you want to supply us the far more information details about the merchandise. We will suggest the item to you in accordance to your requirement of specification. Soon after you affirm, we will prepare the samples to you. also we will supply some good advancements in accordance to your solution use.
nine. Can I arrive to your company to visit?
Sure, you can come to our business to check out at anytime, and welcome to visit our company.
ten. How do speak to us ?
Please send an inquiry
|
US $6-9 / Piece | |
3,000 Pieces (Min. Order) |
###
| Application: | Universal, Industrial, Household Appliances, Car, Power Tools, CCTV Camera |
|---|---|
| Operating Speed: | Low Speed |
| Excitation Mode: | Permanent Magnet |
| Function: | Control |
| Casing Protection: | Drip-Proof |
| Number of Poles: | 4 |
###
| Samples: |
US$ 90/Piece
1 Piece(Min.Order) |
|---|
###
| Customization: |
Available
|
|---|
###
| Model | Application Parameters | Rated Torque of Gear Box | Instant Torque of Gear Box | Gear Ratio | Gear Box Length L1 |
|||||||
| Rated | At No Load | At Rated Load | Overall Length L |
|||||||||
| Voltage | Speed | Current | Speed | Current | Torque | |||||||
| VDC | rpm | mA | rpm | mA | gf.cm | mN.m | mm | gf.cm | gf.cm | mm | ||
| ZWBMD010010-46 | 3.0 | 375 | 80 | 315 | 215 | 39 | 3.8 | 30.9 | 2000 | 6000 | 46 | 15.9 |
| ZWBMD010010-69 | 3.0 | 250 | 80 | 210 | 215 | 58 | 5.7 | 2000 | 6000 | 69 | ||
| ZWBMD010010-102 | 3.0 | 169 | 80 | 142 | 215 | 86 | 8.4 | 2000 | 6000 | 102 | ||
| ZWBMD010010-151 | 3.0 | 114 | 80 | 96 | 215 | 127 | 12.5 | 2000 | 6000 | 151 | ||
| ZWBMD010010-168 | 3.0 | 98 | 80 | 86 | 220 | 106 | 10.4 | 34 | 2000 | 6000 | 168 | 19 |
| ZWBMD010010-249 | 3.0 | 66 | 80 | 58 | 220 | 158 | 15 | 2000 | 6000 | 249 | ||
| ZWBMD010010-368 | 3.0 | 45 | 80 | 39 | 220 | 233 | 23 | 2000 | 6000 | 368 | ||
| ZWBMD010010-546 | 3.0 | 30 | 80 | 27 | 220 | 346 | 34 | 2000 | 6000 | 546 | ||
| ZWBMD010010-809 | 3.0 | 20 | 80 | 18 | 220 | 512 | 50 | 2000 | 6000 | 809 | ||
###
| Smart wearable devices | watch,VR,AR,XR and etc. |
| Household application | kitchen appliances, sewing machines, corn popper, vacuum cleaner, garden tool, sanitary ware, window curtain, intelligent closestool, sweeping robot, power seat, standing desk, electric sofa, TV, computer, treadmill, spyhole, cooker hood, electric drawer, electric mosquito net, intelligent cupboard, intelligent wardrobe, automatic soap dispenser, UV baby bottle sterilizer, lifting hot pot cookware, dishwasher, washing machine, food breaking machine, dryer, air conditioning, dustbin, coffee machine, whisk,smart lock,bread maker,Window cleaning robot and etc. |
| communication equipment | 5G base station,video conference,mobile phone and etc. |
| Office automation equipments | scanners, printers, multifunction machines copy machines, fax (FAX paper cutter), computer peripheral, bank machine, screen, lifting socket, display,notebook PC and etc. |
| Automotive products | conditioning damper actuator, car DVD,door lock actuator, retractable rearview mirror, meters, optic axis control device, head light beam level adjuster, car water pump, car antenna, lumbar support, EPB, car tail gate electric putter, HUD, head-up display, vehicle sunroof, EPS, AGS, car window, head restraint, E-booster, car seat, vehicle charging station and etc. |
| Toys and models | radio control model, automatic cruise control, ride-on toy, educational robot, programming robot, medical robot, automatic feeder, intelligent building blocks, escort robot and etc. |
| Medical equipments | blood pressure meter, breath machine, medical cleaning pump, medical bed, blood pressure monitors, medical ventilator, surgical staplers, infusion pump, dental instrument, self-clotting cutter, wound cleaning pump for orthopedic surgery,electronic cigarette, eyebrow pencil,fascia gun, , surgical robot,laboratory automation and etc. |
| Industrials | flow control valves, seismic testing,automatic reclosing,Agricultural unmanned aerial vehicle,automatic feeder ,intelligent express cabinet and etc. |
| Electric power tools | electric drill, screwdriver,garden tool and etc. |
| Precision instruments | optics instruments,automatic vending machine, wire-stripping machine and etc. |
| Personal care | tooth brush, hair clipper, electric shaver, massager, vibrator, hair dryer, rubdown machine, scissor hair machine, foot grinder,anti-myopia pen, facial beauty equipment, hair curler,Electric threading knife,POWER PERFECT PORE, Puff machine,eyebrow tweezers and etc. |
| Consumer electronics | camera, mobile phone,digital camera, automatic retracting device,camcorder, kinescope DVD,headphone stereo, cassette tape recorder, bluetooth earbud charging case, turntable, tablet,UAV(unmanned aerial vehicle),surveillance camera,PTZ camera, rotating smart speaker and etc. |
| robots | educational robot, programming robot, medical robot, escort robot and etc. |
|
US $6-9 / Piece | |
3,000 Pieces (Min. Order) |
###
| Application: | Universal, Industrial, Household Appliances, Car, Power Tools, CCTV Camera |
|---|---|
| Operating Speed: | Low Speed |
| Excitation Mode: | Permanent Magnet |
| Function: | Control |
| Casing Protection: | Drip-Proof |
| Number of Poles: | 4 |
###
| Samples: |
US$ 90/Piece
1 Piece(Min.Order) |
|---|
###
| Customization: |
Available
|
|---|
###
| Model | Application Parameters | Rated Torque of Gear Box | Instant Torque of Gear Box | Gear Ratio | Gear Box Length L1 |
|||||||
| Rated | At No Load | At Rated Load | Overall Length L |
|||||||||
| Voltage | Speed | Current | Speed | Current | Torque | |||||||
| VDC | rpm | mA | rpm | mA | gf.cm | mN.m | mm | gf.cm | gf.cm | mm | ||
| ZWBMD010010-46 | 3.0 | 375 | 80 | 315 | 215 | 39 | 3.8 | 30.9 | 2000 | 6000 | 46 | 15.9 |
| ZWBMD010010-69 | 3.0 | 250 | 80 | 210 | 215 | 58 | 5.7 | 2000 | 6000 | 69 | ||
| ZWBMD010010-102 | 3.0 | 169 | 80 | 142 | 215 | 86 | 8.4 | 2000 | 6000 | 102 | ||
| ZWBMD010010-151 | 3.0 | 114 | 80 | 96 | 215 | 127 | 12.5 | 2000 | 6000 | 151 | ||
| ZWBMD010010-168 | 3.0 | 98 | 80 | 86 | 220 | 106 | 10.4 | 34 | 2000 | 6000 | 168 | 19 |
| ZWBMD010010-249 | 3.0 | 66 | 80 | 58 | 220 | 158 | 15 | 2000 | 6000 | 249 | ||
| ZWBMD010010-368 | 3.0 | 45 | 80 | 39 | 220 | 233 | 23 | 2000 | 6000 | 368 | ||
| ZWBMD010010-546 | 3.0 | 30 | 80 | 27 | 220 | 346 | 34 | 2000 | 6000 | 546 | ||
| ZWBMD010010-809 | 3.0 | 20 | 80 | 18 | 220 | 512 | 50 | 2000 | 6000 | 809 | ||
###
| Smart wearable devices | watch,VR,AR,XR and etc. |
| Household application | kitchen appliances, sewing machines, corn popper, vacuum cleaner, garden tool, sanitary ware, window curtain, intelligent closestool, sweeping robot, power seat, standing desk, electric sofa, TV, computer, treadmill, spyhole, cooker hood, electric drawer, electric mosquito net, intelligent cupboard, intelligent wardrobe, automatic soap dispenser, UV baby bottle sterilizer, lifting hot pot cookware, dishwasher, washing machine, food breaking machine, dryer, air conditioning, dustbin, coffee machine, whisk,smart lock,bread maker,Window cleaning robot and etc. |
| communication equipment | 5G base station,video conference,mobile phone and etc. |
| Office automation equipments | scanners, printers, multifunction machines copy machines, fax (FAX paper cutter), computer peripheral, bank machine, screen, lifting socket, display,notebook PC and etc. |
| Automotive products | conditioning damper actuator, car DVD,door lock actuator, retractable rearview mirror, meters, optic axis control device, head light beam level adjuster, car water pump, car antenna, lumbar support, EPB, car tail gate electric putter, HUD, head-up display, vehicle sunroof, EPS, AGS, car window, head restraint, E-booster, car seat, vehicle charging station and etc. |
| Toys and models | radio control model, automatic cruise control, ride-on toy, educational robot, programming robot, medical robot, automatic feeder, intelligent building blocks, escort robot and etc. |
| Medical equipments | blood pressure meter, breath machine, medical cleaning pump, medical bed, blood pressure monitors, medical ventilator, surgical staplers, infusion pump, dental instrument, self-clotting cutter, wound cleaning pump for orthopedic surgery,electronic cigarette, eyebrow pencil,fascia gun, , surgical robot,laboratory automation and etc. |
| Industrials | flow control valves, seismic testing,automatic reclosing,Agricultural unmanned aerial vehicle,automatic feeder ,intelligent express cabinet and etc. |
| Electric power tools | electric drill, screwdriver,garden tool and etc. |
| Precision instruments | optics instruments,automatic vending machine, wire-stripping machine and etc. |
| Personal care | tooth brush, hair clipper, electric shaver, massager, vibrator, hair dryer, rubdown machine, scissor hair machine, foot grinder,anti-myopia pen, facial beauty equipment, hair curler,Electric threading knife,POWER PERFECT PORE, Puff machine,eyebrow tweezers and etc. |
| Consumer electronics | camera, mobile phone,digital camera, automatic retracting device,camcorder, kinescope DVD,headphone stereo, cassette tape recorder, bluetooth earbud charging case, turntable, tablet,UAV(unmanned aerial vehicle),surveillance camera,PTZ camera, rotating smart speaker and etc. |
| robots | educational robot, programming robot, medical robot, escort robot and etc. |
Benefits of a Planetary Motor
Besides being one of the most efficient forms of a drive, a Planetary Motor also offers a great number of other benefits. These features enable it to create a vast range of gear reductions, as well as generate higher torques and torque density. Let’s take a closer look at the benefits this mechanism has to offer. To understand what makes it so appealing, we’ll explore the different types of planetary systems.
Solar gear
The solar gear on a planetary motor has two distinct advantages. It produces less noise and heat than a helical gear. Its compact footprint also minimizes noise. It can operate at high speeds without sacrificing efficiency. However, it must be maintained with constant care to operate efficiently. Solar gears can be easily damaged by water and other debris. Solar gears on planetary motors may need to be replaced over time.
A planetary gearbox is composed of a sun gear and two or more planetary ring and spur gears. The sun gear is the primary gear and is driven by the input shaft. The other two gears mesh with the sun gear and engage the stationary ring gear. The three gears are held together by a carrier, which sets the spacing. The output shaft then turns the planetary gears. This creates an output shaft that rotates.
Another advantage of planetary gears is that they can transfer higher torques while being compact. These advantages have led to the creation of solar gears. They can reduce the amount of energy consumed and produce more power. They also provide a longer service life. They are an excellent choice for solar-powered vehicles. But they must be installed by a certified solar energy company. And there are other advantages as well. When you install a solar gear on a planetary motor, the energy produced by the sun will be converted to useful energy.
A solar gear on a planetary motor uses a solar gear to transmit torque from the sun to the planet. This system works on the principle that the sun gear rotates at the same rate as the planet gears. The sun gear has a common design modulus of -Ns/Np. Hence, a 24-tooth sun gear equals a 3-1/2 planet gear ratio. When you consider the efficiency of solar gears on planetary motors, you will be able to determine whether the solar gears are more efficient.
Sun gear
The mechanical arrangement of a planetary motor comprises of two components: a ring gear and a sun gear. The ring gear is fixed to the motor’s output shaft, while the sun gear rolls around and orbits around it. The ring gear and sun gear are linked by a planetary carrier, and the torque they produce is distributed across their teeth. The planetary structure arrangement also reduces backlash, and is critical to achieve a quick start and stop cycle.
When the two planetary gears rotate independently, the sun gear will rotate counterclockwise and the ring-gear will turn in the same direction. The ring-gear assembly is mounted in a carrier. The carrier gear and sun gear are connected to each other by a shaft. The planetary gears and sun gear rotate around each other on the ring-gear carrier to reduce the speed of the output shaft. The planetary gear system can be multiplied or staged to obtain a higher reduction ratio.
A planetary gear motor mimics the planetary rotation system. The input shaft turns a central gear, known as the sun gear, while the planetary gears rotate around a stationary sun gear. The motor’s compact design allows it to be easily mounted to a vehicle, and its low weight makes it ideal for small vehicles. In addition to being highly efficient, a planetary gear motor also offers many other benefits.
A planetary gearbox uses a sun gear to provide torque to the other gears. The planet pinions mesh with an internal tooth ring gear to generate rotation. The carrier also acts as a hub between the input gear and output shaft. The output shaft combines these two components, giving a higher torque. There are three types of planetary gearboxes: the sun gear and a wheel drive planetary gearbox.
Planetary gear
A planetary motor gear works by distributing rotational force along a separating plate and a cylindrical shaft. A shock-absorbing device is included between the separating plate and cylindrical shaft. This depressed portion prevents abrasion wear and foreign particles from entering the device. The separating plate and shaft are positioned coaxially. In this arrangement, the input shaft and output shaft are rotated relative to one another. The rotatable disc absorbs the impact.
Another benefit of a planetary motor gear is its efficiency. Planetary motor gears are highly efficient at transferring power, with 97% of the input energy being transferred to the output. They can also have high gear ratios, and offer low noise and backlash. This design also allows the planetary gearbox to work with electric motors. In addition, planetary gears also have a long service life. The efficiency of planetary gears is due in part to the large number of teeth.
Other benefits of a planetary motor gear include the ease of changing ratios, as well as the reduced safety stock. Unlike other gears, planetary gears don’t require special tools for changing ratios. They are used in numerous industries, and share parts across multiple sizes. This means that they are cost-effective to produce and require less safety stock. They can withstand high shock and wear, and are also compact. If you’re looking for a planetary motor gear, you’ve come to the right place.
The axial end surface of a planetary gear can be worn down by abrasion with a separating plate. In addition, foreign particles may enter the planetary gear device. These particles can damage the gears or even cause noise. As a result, you should check planetary gears for damage and wear. If you’re looking for a gear, make sure it has been thoroughly tested and installed by a professional.
Planetary gearbox
A planetary motor and gearbox are a common combination of electric and mechanical power sources. They share the load of rotation between multiple gear teeth to increase the torque capacity. This design is also more rigid, with low backlash that can be as low as one or two arc minutes. The advantages of a planetary gearmotor over a conventional electric motor include compact size, high efficiency, and less risk of gear failure. Planetary gear motors are also more reliable and durable than conventional electric motors.
A planetary gearbox is designed for a single stage of reduction, or a multiple-stage unit can be built with several individual cartridges. Gear ratios may also be selected according to user preference, either to face mount the output stage or to use a 5mm hex shaft. For multi-stage planetary gearboxes, there are a variety of different options available. These include high-efficiency planetary gearboxes that achieve a 98% efficiency at single reduction. In addition, they are noiseless, and reduce heat loss.
A planetary gearbox may be used to increase torque in a robot or other automated system. There are different types of planetary gear sets available, including gearboxes with sliding or rolling sections. When choosing a planetary gearset, consider the environment and other factors such as backlash, torque, and ratio. There are many advantages to a planetary gearbox and the benefits and drawbacks associated with it.
Planetary gearboxes are similar to those in a solar system. They feature a central sun gear in the middle, two or more outer gears, and a ring gear at the output. The planetary gears rotate in a ring-like structure around a stationary sun gear. When the gears are engaged, they are connected by a carrier that is fixed to the machine’s shaft.
Planetary gear motor
Planetary gear motors reduce the rotational speed of an armature by one or more times. The reduction ratio depends on the structure of the planetary gear device. The planetary gear device has an output shaft and an armature shaft. A separating plate separates the two. The output shaft moves in a circular pattern to turn the pinion 3. When the pinion rotates to the engagement position, it is engaged with the ring gear 4. The ring gear then transmits the rotational torque to the armature shaft. The result is that the engine cranks up.
Planetary gear motors are cylindrical in shape and are available in various power levels. They are typically made of steel or brass and contain multiple gears that share the load. These motors can handle massive power transfers. The planetary gear drive, on the other hand, requires more components, such as a sun’s gear and multiple planetary gears. Consequently, it may not be suitable for all types of applications. Therefore, the planetary gear drive is generally used for more complex machines.
Brush dusts from the electric motor may enter the planetary gear device and cause it to malfunction. In addition, abrasion wear on the separating plate can affect the gear engagement of the planetary gear device. If this occurs, the gears will not engage properly and may make noise. In order to prevent such a situation from occurring, it is important to regularly inspect planetary gear motors and their abrasion-resistant separating plates.
Planetary gear motors come in many different power levels and sizes. These motors are usually cylindrical in shape and are made of steel, brass, plastic, or a combination of both materials. A planetary gear motor can be used in applications where space is an issue. This motor also allows for low gearings in small spaces. The planetary gearing allows for large amounts of power transfer. The output shaft size is dependent on the gear ratio and the motor speed.
editor by czh 2022-12-30
China 12V 100rpm High Torque 16mm DC Planetary Mini Gear Motor for Smart Lock motor electric
Product Description
A. Specification of 12V 100RPM High Torque 16MM DC Planetary Mini Gear Motor for Smart Lock:
1. Voltage: 3/6/12/24V
2. Speed:3-4000RPM
3. Torque: 1-4Kgf.cm
4. Output Power: 0.1-1W
5. Gearbox Ratio: 1:4 to 1: 2418
6. Gearbox Diameter: 16mm
7. Gearbox Length: 15.8-26.6mm
8. Motor Length: 26.9mm
9. Shaft Diameter: 3mm
10. Shaft Length: Customized
Note: The data sheet is only for reference, We can make the motor according to your requirement after Evaluation
B. Company Capacity
HangZhou CZPT Co. Ltd is a manufacturer and exporter of various of motors with over 10 years experience.
Our product ranges include:
1) DC Brush motor: 6-130mm diameter, 0.01-1000W output power
2) DC Spur Gear Motor: 12-110mm diameter, 0.1-300W output power
3) DC Planeary Gear Motor: 10-82mm diameter, 0.1-100W output power
4) Brushless DC Motor: 28-110mm, 5-1500W output power
5) Stepper Motor: NEMA 08 to NEMA 43, Can with gearbox and lead screw
6) Servo Motor: 42mm to 130mm diameter, 50-4000w
7) AC Gear Motor: 49 to 100mm diameter, 6-140 output power
1. Production Line:
2. Certificates:
3. Packing
4. Customer Visits:
5. FAQ:
Q: What’s your main products?
A:We currently produce Brushed Dc Motors, Brushed Dc gear Motors, Planetary Dc Gear Motors, Brushless Dc Motors, Stepper motors and Ac Motors etc. You can check the specifications for above motors on our website and you can email us to recommend needed motors per your specification too.
Q:How to select a suitable motor?
A:If you have motor pictures or drawings to show us, or you have detailed specs like voltage, speed, torque, motor size, working mode of the motor, needed life time and noise level etc, please do not hesitate to let us know, then we can recommend suitable motor per your request accordingly.
Q: Do you have customized service for your standard motors?
A:Yes, we can customize per your request for the voltage, speed, torque and shaft size/shape. If you need additional wires/cables soldered on the terminal or need to add connectors, or capacitors or EMC we can make it too.
Q:Do you have individual design service for motors?
A:Yes, we would like to design motors individually for our customers, but it may need some CZPT charge and design charge.
Q:Can I have samples for testing first?
A:Yes, definitely you can. After confirmed the needed motor specs, we will quote and provide a proforma invoice for samples, once we get the payment, we will get a PASS from our account department to proceed samples accordingly.
Q:How do you make sure motor quality?
A:We have our own inspection procedures: for incoming materials, we have signed sample and drawing to make sure qualified incoming materials; for production process, we have tour inspection in the process and final inspection to make sure qualified products before shipping.
Q:What’s your lead time?
A:Generally speaking, our regular standard product will need 25-30days, a bit longer for customized products. But we are very flexible on the lead time, it will depends on the specific orders
Q:What’s your payment term?
A:For all our new customers, we will need 40% deposite, 60% paid before shipment.
Q:When will you reply after got my inquiries?
A:We will response within 24 hours once get your inquires.
Q:How can I trust you to make sure my money is safe?
A:We are certified by the third party SGS and we have exported to over 85 countries up to June.2017. You can check our reputation with our current customers in your country (if our customers do not mind), or you can order via alibaba to get trade assurance from alibaba to make sure your money is safe.
Q:What’s the minimum order quantity?
A:Our minimum order quantity depends on different motor models, please email us to check. Also, we usually do not accept personal use motor orders.
Q:What’s your shipping method for motors?
A:For samples and packages less than 100kg, we usually suggest express shipping; For heavy packages, we usually suggest air shipping or sea shipping. But it all depends on our customers’ needs.
Q:What certifications do you have?
A:We currently have CE and ROSH certifications.
Q:Can you send me your price list?
A:Since we have hundreds of different products, and price varies per different specifications, we are not CZPT to offer a price list. But we can quote within 24 hours once got your inquirues to make sure you can get the price in time.
Q:Can I visit your company?
A:Yes, welcome to visit our company, but please let us know at least 2 weeks in advance to help us make sure no other meetings during the day you visit us. Thanks!
Weclome contact with us if have any questions about this motor or other products!
| Application: | Universal, Household Appliances, Power Tools, Curtain and Others |
|---|---|
| Operating Speed: | Low Speed |
| Function: | Driving |
| Casing Protection: | Open Type |
| Structure and Working Principle: | Brush |
| Type: | DC Gear Motor |
###
| Samples: |
US$ 15/Piece
1 Piece(Min.Order) |
|---|
###
| Customization: |
Available
|
|---|
| Application: | Universal, Household Appliances, Power Tools, Curtain and Others |
|---|---|
| Operating Speed: | Low Speed |
| Function: | Driving |
| Casing Protection: | Open Type |
| Structure and Working Principle: | Brush |
| Type: | DC Gear Motor |
###
| Samples: |
US$ 15/Piece
1 Piece(Min.Order) |
|---|
###
| Customization: |
Available
|
|---|
The Benefits of Using a Gear Motor
A gear motor works on the principle of conservation of angular momentum. As the smaller gear covers more RPM and the larger gear produces more torque, the ratio between the two is greater than one. Similarly, a multiple gear motor follows the principle of energy conservation, with the direction of rotation always opposite to the one that is adjacent to it. It’s easy to understand the concept behind gear motors and the various types available. Read on to learn about the different types of gears and their applications.
Electric motor
The choice of an electric motor for gear motor is largely dependent on the application. There are various motor and gearhead combinations available, and some are more efficient than others. However, it is critical to understand the application requirements and select a motor that meets these needs. In this article, we’ll examine some of the benefits of using a gear motor. The pros and cons of each type are briefly discussed. You can buy new gear motors at competitive prices, but they aren’t the most reliable or durable option for your application.
To determine which motor is best for your application, you’ll need to consider the load and speed requirements. A gear motor’s efficiency (e) can be calculated by taking the input and output values and calculating their relation. On the graph below, the input (T) and output (P) values are represented as dashed lines. The input (I) value is represented as the torque applied to the motor shaft. The output (P) is the amount of mechanical energy converted. A DC gear motor is 70% efficient at 3.75 lb-in / 2,100 rpm.
In addition to the worm gear motor, you can also choose a compact DC worm gear motor with a variable gear ratio from 7.5 to 80. It has a range of options and can be custom-made for your specific application. The 3-phase AC gear motor, on the other hand, works at a rated power of one hp and torque of 1.143.2 kg-m. The output voltage is typically 220V.
Another important factor is the output shaft orientation. There are two main orientations for gearmotors: in-line and offset. In-line output shafts are most ideal for applications with high torque and short reduction ratios. If you want to avoid backlash, choose a right angle output shaft. An offset shaft can cause the output shaft to become excessively hot. If the output shaft is angled at a certain angle, it may be too large or too small.
Gear reducer
A gear reducer is a special kind of speed reducing motor, usually used in large machinery, such as compressors. These reducers have no cooling fan and are not designed to handle heavy loads. Different purposes require different service factors. For instance, a machine that requires frequent fast accelerations and occasional load spikes needs a gear reducer with a high service factor. A gear reducer that’s designed for long production shifts should be larger than a machine that uses it for short periods of time.
A gear reducer can reduce the speed of a motor by a factor of two. The reduction ratio changes the rotation speed of the receiving member. This change in speed is often required to solve problems of inertia mismatch. The torque density of a gear reducer is measured in newton meters and will depend on the motor used. The first criterion is the configuration of the input and output shafts. A gear ratio of 2:1, for example, means that the output speed has been cut in half.
Bevel gear reducers are a good option if the input and output shafts are perpendicular. This type is very robust and is perfect for situations where the angle between two axes is small. However, bevel gear reducers are expensive and require constant maintenance. They are usually used in heavy-duty conveyors and farm equipment. The correct choice of gear reducer for gear motor is crucial for the efficiency and reliability of the mechanism. To get the best gear reducer for your application, talk to a qualified manufacturer today.
Choosing a gear reducer for a gear motor can be tricky. The wrong one can ruin an entire machine, so it’s important to know the specifics. You must know the torque and speed requirements and choose a motor with the appropriate ratio. A gear reducer should also be compatible with the motor it’s intended for. In some cases, a smaller motor with a gear reducer will work better than a larger one.
Motor shaft
Proper alignment of the motor shaft can greatly improve the performance and life span of rotating devices. The proper alignment of motors and driven instruments enhances the transfer of energy from the motor to the instrument. Incorrect alignment leads to additional noise and vibration. It may also lead to premature failure of couplings and bearings. Misalignment also results in increased shaft and coupling temperatures. Hence, proper alignment is critical to improve the efficiency of the driven instrument.
When choosing the correct type of gear train for your motor, you need to consider its energy efficiency and the torque it can handle. A helical geared motor is more efficient for high output torque applications. Depending on the required speed and torque, you can choose between an in-line and a parallel helical geared motor. Both types of gears have their advantages and disadvantages. Spur gears are widespread. They are toothed and run parallel to the motor shaft.
A planetary gear motor can also have a linear output shaft. A stepping motor should not operate at too high current to prevent demagnetization, which will lead to step loss or torque drop. Ensure that the motor and gearbox output shafts are protected from external impacts. If the motor and gearbox are not protected against bumps, they may cause thread defects. Make sure that the motor shafts and rotors are protected from external impacts.
When choosing a metal for your gear motor’s motor shaft, you should consider the cost of hot-rolled bar stock. Its outer layers are more difficult to machine. This type of material contains residual stresses and other problems that make it difficult to machine. For these applications, you should choose a high-strength steel with hard outer layers. This type of steel is cheaper, but it also has size considerations. It’s best to test each material first to determine which one suits your needs.
In addition to reducing the speed of your device, a geared motor also minimizes the torque generated by your machine. It can be used with both AC and DC power. A high-quality gear motor is vital for stirring mechanisms and conveyor belts. However, you should choose a geared motor that uses high-grade gears and provides maximum efficiency. There are many types of planetary gear motors and gears on the market, and it’s important to choose the right one.
First stage gears
The first stage gears of a gear motor are the most important components of the entire device. The motor’s power transmission is 90% efficient, but there are many factors that can affect its performance. The gear ratios used should be high enough to handle the load, but not too high that they are limiting the motor’s speed. A gear motor should also have a healthy safety factor, and the lubricant must be sufficient to overcome any of these factors.
The transmission torque of the gear changes with its speed. The transmission torque at the input side of the gear decreases, transferring a small torque to the output side. The number of teeth and the pitch circle diameters can be used to calculate the torque. The first stage gears of gear motors can be categorized as spur gears, helical gears, or worm gears. These three types of gears have different torque capacities.
The first stage helical gear is the most important part of a gear motor. Its function is to transfer rotation from one gear to the other. Its output is the gearhead. The second stage gears are connected by a carrier. They work in tandem with the first stage gear to provide the output of the gearhead. Moreover, the first stage carrier rotates in the same direction as the input pinion.
Another important component is the output torque of the gearmotor. When choosing a gearmotor, consider the starting torque, running torque, output speed, overhung and shock loads, duty cycles, and more. It is crucial to choose a gearmotor with the right ratio for the application. By choosing the proper gearmotor, you will get maximum performance with minimal operating costs and increase plant productivity. For more information on first stage gears, check out our blog.
The first stage of a gear motor is composed of a set of fixed and rotating sprockets. The first stage of these gears acts as a drive gear. Its rotational mass is a limiting factor for torque. The second stage consists of a rotating shaft. This shaft rotates in the direction of the torque axis. It is also the limiting force for the motor’s torque.
editor by czh 2022-12-02
China supplier 10mm 12v motor high torque dc gear motor with wheel with Best Sales
Warranty: 3months-1year
Product Quantity: DGS10-M10 07
Usage: BOAT, Auto, Electric Bicycle, Admirer, House Appliance
Torque: Requests
Development: Long term Magnet
Commutation: Brush
Defend Function: Drip-proof
Speed(RPM): 45RPM
Ongoing Recent(A): .03A
Efficiency: IE one
Description: 10mm 12v motor high torque dc gear motor with wheel
No Load Voltage: 6v or 12 as tailored
No Load Pace: 45±10% rpm
Shaft Size: 3mm or custom
Stall torque: one hundred sixty five g.cm
Load current: .06A
Shaft Dia.: 1.5mm
Reduction Ratio: 171:1 customize
Stall recent: .16A
ODM/OEM: Available
Certification: CCC, ce, RoHS
Packaging Information: Packaging can be tailored in accordance to customer’s request
Port: HangZhou
one.5v minimal velocity 60rpm plastic gearbox micro dc equipment motor
1. Voltage: DC 1.5V2. No load pace: 45±10%rpm3. No load present: .032A4. Diameter 10mm, duration 20mm, shaft dia 1.5mm5. Substance: plastic gear and metal dc motor6. Fat: 10g Approx7. Application:Robot, Bicycle lock, Home Equipment, Doorway Lock etc8. Tailored,Modify the efficiency at free(voltage, speed, torque)Datasheet and Specification: Packaging & DeliveryPacking & Transport
Packaging Specifics:
Carton Meas:32*28*26cm
N.W.:20KGS , G.W.:21KGS
500pcs+Foam box (or plastic box)+Standard Carton
Supply Time: 1-2 months for sample3-4 weeks for mass creation
| Transport Technique | Shipping Time | Rewards & Disadvantages |
| Categorical like DHL/UPS/FEDEX/TNT | 3-5 days with monitoring number | Rapidly and high-priced, doorway to door. |
| Air Shipping | three-5 times | Quickly, airport to airport, customers have to select up the products in the airport |
| Sea Transport | fifteen-thirty days | Inexpensive and gradual, 70HP tractors for agriculture utilised CZPT model not outdated tractor with backhoe loader port to port, clients have to choose up the products in the port |
Our Providers
Our organization provides 1st-course providers to our clientele:
one,we can propose the ideal and specialist solution in accordance to our client‘s product or ask for.
2,one hundred% good quality promise for our solution
3,rapidly shipping time
4,OEM & ODM Series are available
five,instantly reply you inside 24 hours
6,the professional testing
7,the greatest soon after-sale services
Certificate:
Business Information
SHEN ZHEN XIN XIHU (WEST LAKE) DIS. HUI Technologies CO.,LTD
Started in 2003, Xihu (West Lake) Dis.hui Motor is a non-public substantial-tech company, and largely engaged in the style, advancement, manufacturing, sale and services of precision DC motors and gear motors.
About us:
1. Our major goods: Dia4~100mm DC Micro Motor, Vehicle dc motor, Electric powered motor,Coreless Brushless motor, Equipment Motor, DC Motor, Brush DC motor, Forest products Harvester bar in agriculture machinery components for .404 .080 harvester chain Spur Equipment motor, Micro Motor, Vibration motor etc.
two. Products dimension variety: Diameter: 4-100mm
three. DC Voltage selection: 1.5V -42V
AC rectify: 100V, 110V, 220V, 230V, 240V and so forth
4. Velocity variety: 1 RPM-30,000RPM
five. Stall torque: 1g.cm-30kg.cm
6. Software: Home appliance, Electricity Equipment, Toys & Design, Precision Instrument, Business office tools, Personalized treatment product, Automotive, Audio& Visual equipment and many others.
Company & Manufacturing facility Displays:
FAQ
Question 1:What is actually your primary goods?Response: Dia10~52mm DC Micro Motor and Gear Motor,Car dc motor, Electrical motor, Equipment Motor, DC Motor, Brush DC motor, China TY254 25hp four wheel drive 25hp four wheel drive agricultural farm diesel electric powered tracto mini tubr PTO tractor for garden Brushless DC motor,Spur Equipment motor, Micro Motor, Vibration motor and many others.
Question 2:What’s the primary use of the micro dc equipment motor?
Response: Our motor extensively utilised in Property Equipment,Place of work Gear,Well being-treatment equipment,Sanitation business, High-class toy,Banking Method,Electronic and electrical instruments,automation industry, bank equipments,payment equipments,vending equipment,electrical power door lock,electrical door lock.
Question 3:Do you take customize?Reply: Sure,as we have a strong design team,any difficulties will get our complex response.Question 4:What sort of knowledge do i neet to offer if i want to order?Reply: Make sure you kindly inform us your voltage,velocity,torque and all round dimension.Question 5:What if i will not know the previously mentioned knowledge?Answer: Remember to get in touch with our saleman to manage,we’ll response your queries patiently.
What Is a Gear Motor?
A gear motor is an electric motor coupled with a gear train. It uses either DC or AC power to achieve its purpose. The primary benefit of a gear reducer is its ability to multiply torque while maintaining a compact size. The trade-off of this additional torque comes in the form of a reduced output shaft speed and overall efficiency. However, proper gear technology and ratios provide optimum output and speed profiles. This type of motor unlocks the full potential of OEM equipment.
Inertial load
Inertial load on a gear motor is the amount of force a rotating device produces due to its inverse square relationship with its inertia. The greater the inertia, the less torque can be produced by the gear motor. However, if the inertia is too high, it can cause problems with positioning, settling time, and controlling torque and velocity. Gear ratios should be selected for optimal power transfer.
The duration of acceleration and braking time of a gear motor depends on the type of driven load. An inertia load requires longer acceleration time whereas a friction load requires breakaway torque to start the load and maintain it at its desired speed. Too short a time period can cause excessive gear loading and may result in damaged gears. A safe approach is to disconnect the load when power is disconnected to prevent inertia from driving back through the output shaft.
Inertia is a fundamental concept in the design of motors and drive systems. The ratio of mass and inertia of a load to a motor determines how well the motor can control its speed during acceleration or deceleration. The mass moment of inertia, also called rotational inertia, is dependent on the mass, geometry, and center of mass of an object.
Applications
There are many applications of gear motors. They provide a powerful yet efficient means of speed and torque control. They can be either AC or DC, and the two most common motor types are the three-phase asynchronous and the permanent magnet synchronous servomotor. The type of motor used for a given application will determine its cost, reliability, and complexity. Gear motors are typically used in applications where high torque is required and space or power constraints are significant.
There are two types of gear motors. Depending on the ratio, each gear has an output shaft and an input shaft. Gear motors use hydraulic pressure to produce torque. The pressure builds on one side of the motor until it generates enough torque to power a rotating load. This type of motors is not recommended for applications where load reversals occur, as the holding torque will diminish with age and shaft vibration. However, it can be used for precision applications.
The market landscape shows the competitive environment of the gear motor industry. This report also highlights key items, income and value creation by region and country. The report also examines the competitive landscape by region, including the United States, China, India, the GCC, South Africa, Brazil, and the rest of the world. It is important to note that the report contains segment-specific information, so that readers can easily understand the market potential of the geared motors market.
Size
The safety factor, or SF, of a gear motor is an important consideration when selecting one for a particular application. It compensates for the stresses placed on the gearing and enables it to run at maximum efficiency. Manufacturers provide tables detailing typical applications, with multiplication factors for duty. A gear motor with a SF of three or more is suitable for difficult applications, while a gearmotor with a SF of one or two is suitable for relatively easy applications.
The global gear motor market is highly fragmented, with numerous small players catering to various end-use industries. The report identifies various industry trends and provides comprehensive information on the market. It outlines historical data and offers valuable insights on the industry. The report also employs several methodologies and approaches to analyze the market. In addition to providing historical data, it includes detailed information by market segment. In-depth analysis of market segments is provided to help identify which technologies will be most suitable for which applications.
Cost
A gear motor is an electric motor that is paired with a gear train. They are available in AC or DC power systems. Compared to conventional motors, gear reducers can maximize torque while maintaining compact dimensions. But the trade-off is the reduced output shaft speed and overall efficiency. However, when used correctly, a gear motor can produce optimal output and mechanical fit. To understand how a gear motor works, let’s look at two types: right-angle geared motors and inline geared motors. The first two types are usually used in automation equipment and in agricultural and medical applications. The latter type is designed for rugged applications.
In addition to its efficiency, DC gear motors are space-saving and have low energy consumption. They can be used in a number of applications including money counters and printers. Automatic window machines and curtains, glass curtain walls, and banknote vending machines are some of the other major applications of these motors. They can cost up to 10 horsepower, which is a lot for an industrial machine. However, these are not all-out expensive.
Electric gear motors are versatile and widely used. However, they do not work well in applications requiring high shaft speed and torque. Examples of these include conveyor drives, frozen beverage machines, and medical tools. These applications require high shaft speed, so gear motors are not ideal for these applications. However, if noise and other problems are not a concern, a motor-only solution may be the better choice. This way, you can use a single motor for multiple applications.
Maintenance
Geared motors are among the most common equipment used for drive trains. Proper maintenance can prevent damage and maximize their efficiency. A guide to gear motor maintenance is available from WEG. To prevent further damage, follow these maintenance steps:
Regularly check electrical connections. Check for loose connections and torque them to the recommended values. Also, check the contacts and relays to make sure they are not tangled or damaged. Check the environment around the gear motor to prevent dust from clogging the passageway of electric current. A proper maintenance plan will help you identify problems and extend their life. The manual will also tell you about any problems with the gearmotor. However, this is not enough – it is important to check the condition of the gearbox and its parts.
Conduct visual inspection. The purpose of visual inspection is to note any irregularities that may indicate possible problems with the gear motor. A dirty motor may be an indication of a rough environment and a lot of problems. You can also perform a smell test. If you can smell a burned odor coming from the windings, there may be an overheating problem. Overheating can cause the windings to burn and damage.
Reactive maintenance is the most common method of motor maintenance. In this type of maintenance, you only perform repairs if the motor stops working due to a malfunction. Regular inspection is necessary to avoid unexpected motor failures. By using a logbook to document motor operations, you can determine when it is time to replace the gear motor. In contrast to preventive maintenance, reactive maintenance requires no regular tests or services. However, it is recommended to perform inspections every six months.
in Cuttack India sales price shop near me near me shop factory supplier 36mm Dia 12V 24V 30kg. Cm High Torque DC Planetary Gear Motor for Ventilator manufacturer best Cost Custom Cheap wholesaler
a specialized supplier of a entire selection of chains, sprockets, gears, equipment racks, V-belts, couplings and reducers. EPG has set up a full set of good quality management system which is presented with superior inspection and examination gear. The large specific CNC equipment, this kind of as Gradual-feeding wire-minimize equipment, jig grinding equipment and electrical discharge device, ensures the top quality precision of mould processing, with the large efficient and environmental security acid rolling line getting the premier raw substance converting tools in the area in china The wildly use of automated milling equipment, higher-velocity automatic feeding punch, higher pace computerized rolling and assembling machine guarantees the substantial top quality and performance of parts and chain producing. Be aware:
The requirements can be designed according to the customer’s requirements!
Software:
Electric Drill, ScrewEPTr, Scanners, Printers, Vending EPT, Window Curtain, Espresso EPT, Electric Lock, and many others.
Parameter:
| Reduction ratio | 1/five | 1/fourteen | 1/19 | one/27 | 1/fifty one | 1/71 | 1/one hundred | one/139 | one/189 | 1/264 | 1/516 | one/721 | |
| 12V | Rated torque(Kg.cm) | one.one | two.five | 3.six | 5. | 8.two | eleven.5 | sixteen | 20 | twenty five | twenty five | thirty | 30 |
| Rated pace(rpm) | 1250 | 475 | 340 | 243 | 129 | 92 | sixty six | forty seven.2 | 34.8 | twenty five.one | 13.two | 9.five | |
| 24V | Rated torque(Kg.cm) | one.1 | two.7 | 3.eight | five.3 | 8.7 | 12 | seventeen | twenty | 25 | twenty five | 30 | thirty |
| Rated speed(rpm) | 1240 | 470 | 335 | 240 | 127 | 91 | sixty five | forty six.five | 34.3 | 24.8 | 13 | nine.4 | |
| Rotation path | CCW | ||||||||||||
| Length(L-mm) | 33.one | 41.8 | fifty.five | fifty nine.2 | |||||||||
| Rated volt(V) | Rated torque(g.cm) | Rated pace(rpm) | Rated existing(mA) | No-load velocity(rpm) | No load present(mA) | Weight(g) |
| 12 | 270 | 6570 | lt=2050 | 7500 | lt=300 | 222 |
| 24 | 285 | 6480 | lt=1050 | 7500 | lt=210 | 224 |
About Us:
We EPTized in researching, deveXiHu (West Lake) Dis.Hu (West Lake) Dis.ing, and servicing electrical motors, EPT, and higher precision EPTs with the small module. Following a long time of deveXiHu (West Lake) Dis.Hu (West Lake) Dis.ment, we have an unbiased product design and R ampD staff, services crew, and a specialist good quality handle team. To understand our support principle better, offer substantial-quality merchandise and superb services, we have been committed to the core capacity and instruction. We have a EPT manufacturing facility in NanEPTg, which generates higher precision small mildew EPTs, EPT shaft, EPT, and planetary EPT assembling.
Perform-stream:
Certification:
RoHS, CE, and far more…
Provider:
ODM amp OEM
EPT layout and deveXiHu (West Lake) Dis.Hu (West Lake) Dis.ment
Deal ampShip:
Carton, pallet, or what you want
The delivery time is about 30-45 times.
Customer’s Visiting:
FAQ:
one. Can you personalized EPT?
Indeed.
two. DO you offer the sample?
Yes.
3. Do you supply specialized support?
Sure
four. Do you have a factory?
Sure, we are a specialist maker.
five. Can I occur to your business to visit?
Indeed
